[要約] RFC 3621はPower Ethernet MIB(Management Information Base)に関する規格であり、Power over Ethernet(PoE)デバイスの管理と制御を目的としています。この規格は、PoEデバイスの電力供給状態やパフォーマンスを監視し、ネットワーク管理者に情報を提供するために使用されます。

Network Working Group                                          A. Berger
Request for Comments: 3621                               PowerDsine Inc.
Category: Standards Track                                   D. Romascanu
                                                                   Avaya
                                                           December 2003
        

Power Ethernet MIB

パワーイーサネットMIB

Status of this Memo

本文書の位置付け

This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.

このドキュメントは、インターネットコミュニティのインターネット標準トラックプロトコルを指定し、改善のための議論と提案を要求します。このプロトコルの標準化状態とステータスについては、「インターネット公式プロトコル標準」(STD 1)の現在のエディションを参照してください。このメモの配布は無制限です。

Copyright Notice

著作権表示

Copyright (C) The Internet Society (2003). All Rights Reserved.

Copyright(c)The Internet Society(2003)。無断転載を禁じます。

Abstract

概要

This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. This document proposes an extension to the Ethernet-like Interfaces MIB with a set of objects for managing Power Sourcing Equipment (PSE).

このメモは、インターネットコミュニティのネットワーク管理プロトコルで使用するための管理情報ベース(MIB)の一部を定義します。このドキュメントでは、イーサネットのようなインターフェイスMIBへの拡張が、電源機器を管理するための一連のオブジェクト(PSE)を提案しています。

Table of Contents

目次

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  2
   2.  The Internet-Standard Management Framework . . . . . . . . . .  2
   3.  Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
   4.  MIB Structure. . . . . . . . . . . . . . . . . . . . . . . . .  3
   5.  Definitions. . . . . . . . . . . . . . . . . . . . . . . . . .  3
   6.  Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 16
   7.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 16
       7.1.  Normative References . . . . . . . . . . . . . . . . . . 16
       7.2.  Informative References . . . . . . . . . . . . . . . . . 17
   8.  Intellectual Property Statement. . . . . . . . . . . . . . . . 17
   9.  Security Considerations. . . . . . . . . . . . . . . . . . . . 18
   10. Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 19
   11. Full Copyright Statement . . . . . . . . . . . . . . . . . . . 20
        
1. Introduction
1. はじめに

This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it defines a set of MIB objects to manage Power Ethernet [IEEE-802.3af] Power Sourcing Equipment (PSE).

このメモは、インターネットコミュニティのネットワーク管理プロトコルで使用するための管理情報ベース(MIB)の一部を定義します。特に、Power Ethernet [IEEE-802.3AF] Power Sourcing装置(PSE)を管理するMIBオブジェクトのセットを定義します。

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119].

「必須」、「そうしない」、「必須」、「必要」、「「しない」、「そうでない」、「そうではない」、「そうでない」、「推奨」、「5月」、および「オプション」は、[RFC2119]に記載されているように解釈される。

2. The Internet-Standard Management Framework
2. インターネット標準の管理フレームワーク

For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410].

現在のインターネット標準管理フレームワークを説明するドキュメントの詳細な概要については、RFC 3410 [RFC3410]のセクション7を参照してください。

Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580].

管理されたオブジェクトは、管理情報ベースまたはMIBと呼ばれる仮想情報ストアからアクセスされます。MIBオブジェクトは通常、単純なネットワーク管理プロトコル(SNMP)からアクセスされます。MIBのオブジェクトは、管理情報の構造(SMI)で定義されたメカニズムを使用して定義されます。このメモは、STD 58、RFC 2578 [RFC2578]、STD 58、RFC 2579 [RFC2579]およびSTD 58、RFC 2580 [RFC2580]に記載されているSMIV2に準拠したMIBモジュールを指定します。

3. Overview
3. 概要

The emergence of IP telephony as an application that allows voice applications to be run over the same infrastructure as data applications has led to the emergence of Ethernet IP phones, which have similar functions and characteristics as traditional phones. Powering the phone with the same cable used for signal transfer is one of the functions that are being taken as granted. The IEEE 802.3 Working Group has initiated standardization on this subject, currently known as the IEEE 802.3af work [IEEE-802.3af].

データアプリケーションと同じインフラストラクチャで音声アプリケーションを実行できるようにするアプリケーションとしてのIPテレフォニーの出現により、従来の電話と同様の機能と特性があるイーサネットIP電話の出現が生じています。信号転送に使用されるのと同じケーブルで電話に電源を入れることは、付与されているように使用されている機能の1つです。IEEE 802.3ワーキンググループは、現在IEEE 802.3AF作業[IEEE-802.3AF]として知られているこのテーマに関する標準化を開始しました。

The IEEE 802.3af WG did not define a full management interface, but only the hardware registers that will allow for management interfaces to be built for a powered Ethernet device. The MIB module defined in this document extends the Ethernet-like Interfaces MIB [RFC3635] with the management objects required for the management of the powered Ethernet devices and ports.

IEEE 802.3AF WGは、完全な管理インターフェイスを定義しませんでしたが、管理インターフェイスをパワーイーサネットデバイス用に構築できるハードウェアレジスタのみが定義されています。このドキュメントで定義されているMIBモジュールは、イーサネットのようなインターフェイスMIB [RFC3635]を、電動イーサネットデバイスとポートの管理に必要な管理オブジェクトと拡張します。

The following abbreviations are defined in [IEEE-802.3af] and will be used with the same significance in this document:

次の略語は[IEEE-802.3AF]で定義されており、このドキュメントでは同じ重要性で使用されます。

PSE - Power Sourcing Equipment;

PSE-電源供給装置。

PD - Powered Device

PD-電動デバイス

4. MIB Structure
4. MIB構造

These MIB objects are categorized into three MIB groups.

これらのMIBオブジェクトは、3つのMIBグループに分類されます。

The pethPsePortTable defines the objects used for configuring and describing the status of ports on a PSE device. Examples of PSE devices are Ethernet switches that support power Ethernet and mid-span boxes.

Pethpseporttableは、PSEデバイス上のポートのステータスの構成と記述に使用されるオブジェクトを定義します。PSEデバイスの例は、パワーイーサネットとミッドスパンボックスをサポートするイーサネットスイッチです。

The pethMainPseObjects MIB group defines the management objects for a managed main power source in a PSE device. Ethernet switches are one example of boxes that would support these objects.

PethmainPseObjects MIBグループは、PSEデバイスの管理された主要な電源の管理オブジェクトを定義します。イーサネットスイッチは、これらのオブジェクトをサポートするボックスの一例です。

The pethNotificationControlTable includes objects that control the transmission of notifications from the agent to a management application.

PethnotificationControltableには、エージェントから管理アプリケーションへの通知の送信を制御するオブジェクトが含まれています。

5. Definitions
5. 定義
POWER-ETHERNET-MIB DEFINITIONS ::= BEGIN
        

IMPORTS MODULE-IDENTITY, mib-2, OBJECT-TYPE, Integer32, Gauge32, Counter32, NOTIFICATION-TYPE FROM SNMPv2-SMI TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF

インポートモジュールアイデンティティ、MIB-2、オブジェクトタイプ、integer32、ゲージ32、カウンター32、SNMPV2-TCモジュール違反からのSNMPV2-SMI TruthValueの通知型、オブジェクトグループ、SNMPV2-CONFからの通知グループ

SnmpAdminString FROM SNMP-FRAMEWORK-MIB;

snmp-framework-mibからのsnmpadminstring;

powerEthernetMIB MODULE-IDENTITY

PowerEthernetMibモジュール同一性

LAST-UPDATED "200311240000Z" -- November 24, 2003 ORGANIZATION "IETF Ethernet Interfaces and Hub MIB Working Group"

最終的なアップデート「200311240000Z」 - 2003年11月24日組織「IETFイーサネットインターフェイスとハブMIBワーキンググループ」

CONTACT-INFO " WG Charter: http://www.ietf.org/html.charters/hubmib-charter.html

contact-info "WGチャーター:http://www.ietf.org/html.charters/hubmib-charter.html

         Mailing lists:
          General Discussion: hubmib@ietf.org
          To Subscribe: hubmib-requests@ietf.org
          In Body: subscribe your_email_address
        

Chair: Dan Romascanu Avaya Tel: +972-3-645-8414 Email: dromasca@avaya.com

椅子:Dan Romascanu Avaya Tel:972-3-645-8414メール:dromasca@avaya.com

Editor: Avi Berger PowerDsine Inc. Tel: 972-9-7755100 Ext 307 Fax: 972-9-7755120 E-mail: avib@PowerDsine.com "

編集者:Avi Berger Powerdsine Inc. Tel:972-9-7755100 Ext 307 Fax:972-9-7755120電子メール:avib@powerdsine.com "

DESCRIPTION "The MIB module for managing Power Source Equipment (PSE) working according to the IEEE 802.af Powered Ethernet (DTE Power via MDI) standard.

説明「IEEE 802.AFパワーイーサネット(MDI経由のDTE電力)標準に従って動作する電源機器(PSE)を管理するためのMIBモジュール。

The following terms are used throughout this MIB module. For complete formal definitions, the IEEE 802.3 standards should be consulted wherever possible:

次の用語は、このMIBモジュール全体で使用されます。完全な正式な定義のために、可能な限りIEEE 802.3基準に相談する必要があります。

Group - A recommended, but optional, entity defined by the IEEE 802.3 management standard, in order to support a modular numbering scheme. The classical example allows an implementor to represent field-replaceable units as groups of ports, with the port numbering matching the modular hardware implementation.

グループ - モジュラー番号スキームをサポートするために、IEEE 802.3管理標準で定義された推奨される、しかしオプションのエンティティ。古典的な例では、実装者はフィールド補充可能ユニットをポートのグループとして表すことができ、ポート番号はモジュラーハードウェアの実装に一致します。

Port - This entity identifies the port within the group for which this entry contains information. The numbering scheme for ports is implementation specific.

ポート - このエンティティは、このエントリに情報が含まれているグループ内のポートを識別します。ポートの番号付けスキームは実装固有です。

Copyright (c) The Internet Society (2003). This version of this MIB module is part of RFC 3621; See the RFC itself for full legal notices."

Copyright(c)The Internet Society(2003)。このMIBモジュールのこのバージョンは、RFC 3621の一部です。完全な法的通知については、RFC自体を参照してください。」

       REVISION    "200311240000Z"  -- November 24, 2003
       DESCRIPTION "Initial version, published as RFC 3621."
       ::= { mib-2 105 }
        
pethNotifications OBJECT IDENTIFIER ::= { powerEthernetMIB 0 }
pethObjects       OBJECT IDENTIFIER ::= { powerEthernetMIB 1 }
pethConformance   OBJECT IDENTIFIER ::= { powerEthernetMIB 2 }
        

-- PSE Objects

-PSEオブジェクト

  pethPsePortTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF PethPsePortEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table of objects that display and control the power
            characteristics of power Ethernet ports on a Power Source
            Entity (PSE) device.  This group will be implemented in
            managed power Ethernet switches and mid-span devices.
            Values of all read-write objects in this table are
            persistent at restart/reboot."
       ::= { pethObjects 1 }
        
   pethPsePortEntry OBJECT-TYPE
       SYNTAX      PethPsePortEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
               "A set of objects that display and control the power
               characteristics of a power Ethernet PSE port."
       INDEX    { pethPsePortGroupIndex , pethPsePortIndex  }
       ::= { pethPsePortTable 1 }
        
   PethPsePortEntry ::= SEQUENCE {
       pethPsePortGroupIndex
          Integer32,
       pethPsePortIndex
          Integer32,
       pethPsePortAdminEnable
          TruthValue,
       pethPsePortPowerPairsControlAbility
          TruthValue,
       pethPsePortPowerPairs
          INTEGER,
       pethPsePortDetectionStatus
          INTEGER,
       pethPsePortPowerPriority
          INTEGER,
        

pethPsePortMPSAbsentCounter Counter32, pethPsePortType SnmpAdminString, pethPsePortPowerClassifications INTEGER, pethPsePortInvalidSignatureCounter Counter32, pethPsePortPowerDeniedCounter Counter32, pethPsePortOverLoadCounter Counter32, pethPsePortShortCounter Counter32 }

PethpseportmpsabsEntcounter counter32、pethpseporttype snmpadminstring、pethpseportpowerclassifications integer、pethpseportinvalidsignaturecounter counter32、pethpseportpowerdeniedc counter 32、カウンターカウンターカウンターカウンターカウンターカウンターカウンター

     pethPsePortGroupIndex OBJECT-TYPE
       SYNTAX      Integer32 (1..2147483647)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This variable uniquely identifies the group
            containing the port to which a power Ethernet PSE is
            connected.  Group means box in the stack, module in a
            rack and the value 1 MUST be used for non-modular devices.
            Furthermore, the same value MUST be used in this variable,
            pethMainPseGroupIndex, and pethNotificationControlGroupIndex
            to refer to a given box in a stack or module in the rack."
       ::= { pethPsePortEntry 1 }
        
     pethPsePortIndex OBJECT-TYPE
       SYNTAX      Integer32 (1..2147483647)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This variable uniquely identifies the power Ethernet PSE
            port within group pethPsePortGroupIndex to which the
            power Ethernet PSE entry is connected."
       ::= { pethPsePortEntry 2 }
        

pethPsePortAdminEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "true (1) An interface which can provide the PSE functions. false(2) The interface will act as it would if it had no PSE function."

pethpseportadminenable object-type struthvalue max-access read-writeステータス現在の説明 "true(1)pse関数を提供できるインターフェイス。false(2)インターフェイスは、PSE関数がない場合に機能します。」

    REFERENCE
      "IEEE Std 802.3af Section 30.9.1.1.2 aPSEAdminState"
    ::= { pethPsePortEntry 3 }
        
     pethPsePortPowerPairsControlAbility OBJECT-TYPE
    SYNTAX TruthValue
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION
        "Describes the capability of controlling the power pairs
         functionality to switch pins for sourcing power.
         The value true indicate that the device has the capability
         to control the power pairs.  When false the PSE Pinout
         Alternative used cannot be controlled through the
         PethPsePortAdminEnable attribute."
    REFERENCE
      "IEEE Std 802.3af Section 30.9.1.1.3
       aPSEPowerPairsControlAbility"
    ::= { pethPsePortEntry 4 }
        
    pethPsePortPowerPairs OBJECT-TYPE
    SYNTAX INTEGER   {
               signal(1),
               spare(2)
     }
    MAX-ACCESS read-write
    STATUS current
    DESCRIPTION
        "Describes or controls the pairs in use.  If the value of
         pethPsePortPowerPairsControl is true, this object is
         writable.
         A value of signal(1) means that the signal pairs
         only are in use.
         A value of spare(2) means that the spare pairs
         only are in use."
    REFERENCE
      "IEEE Std 802.3af Section 30.9.1.1.4 aPSEPowerPairs"
    ::= { pethPsePortEntry 5 }
        
     pethPsePortDetectionStatus OBJECT-TYPE
    SYNTAX INTEGER   {
             disabled(1),
             searching(2),
               deliveringPower(3),
               fault(4),
               test(5),
               otherFault(6)
     }
        
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION
        "Describes the operational status of the port PD detection.
         A value of disabled(1)- indicates that the PSE State diagram
         is in the state DISABLED.
         A value of deliveringPower(3) - indicates that the PSE State
         diagram is in the state POWER_ON for a duration greater than
         tlim max (see IEEE Std 802.3af Table 33-5 tlim).
         A value of fault(4) - indicates that the PSE State diagram is
         in the state TEST_ERROR.
         A value of test(5) - indicates that the PSE State diagram is
         in the state TEST_MODE.
         A value of otherFault(6) - indicates that the PSE State
         diagram is in the state IDLE due to the variable
         error_conditions.
         A value of searching(2)- indicates the PSE State diagram is
         in a state other than those listed above."
    REFERENCE
      "IEEE Std 802.3af Section 30.9.1.1.5
       aPSEPowerDetectionStatus"
    ::= { pethPsePortEntry 6 }
        
     pethPsePortPowerPriority OBJECT-TYPE
    SYNTAX INTEGER   {
               critical(1),
               high(2),
               low(3)
     }
    MAX-ACCESS read-write
    STATUS current
    DESCRIPTION
        "This object controls the priority of the port from the point
         of view of a power management algorithm.  The priority that
         is set by this variable could be used by a control mechanism
         that prevents over current situations by disconnecting first
         ports with lower power priority.  Ports that connect devices
         critical to the operation of the network - like the E911
         telephones ports - should be set to higher priority."
    ::= { pethPsePortEntry 7 }
        
   pethPsePortMPSAbsentCounter OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION
          "This counter is incremented when the PSE state diagram
             transitions directly from the state POWER_ON to the
                state IDLE due to tmpdo_timer_done being asserted."
    REFERENCE
      "IEEE Std 802.3af Section 30.9.1.1.11
       aPSEMPSAbsentCounter"
    ::= { pethPsePortEntry 8 }
        
   pethPsePortType OBJECT-TYPE
    SYNTAX SnmpAdminString
    MAX-ACCESS read-write
    STATUS current
    DESCRIPTION
        "A manager will set the value of this variable to indicate
         the type of powered device that is connected to the port.
         The default value supplied by the agent if no value has
         ever been set should be a zero-length octet string."
    ::= { pethPsePortEntry 9 }
        
    pethPsePortPowerClassifications OBJECT-TYPE
     SYNTAX INTEGER   {
               class0(1),
               class1(2),
               class2(3),
               class3(4),
               class4(5)
     }
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION
        "Classification is a way to tag different terminals on the
        Power over LAN network according to their power consumption.
        Devices such as IP telephones, WLAN access points and others,
        will be classified according to their power requirements.
        

The meaning of the classification labels is defined in the IEEE specification.

分類ラベルの意味は、IEEE仕様で定義されています。

       This variable is valid only while a PD is being powered,
        that is, while the attribute pethPsePortDetectionStatus
        is reporting the enumeration deliveringPower."
    REFERENCE
      "IEEE Std 802.3af Section 30.9.1.1.6
       aPSEPowerClassification"
   ::= { pethPsePortEntry 10 }
        
   pethPsePortInvalidSignatureCounter OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
       DESCRIPTION
       "This counter is incremented when the PSE state diagram
         enters the state SIGNATURE_INVALID."
    REFERENCE
          "IEEE Std 802.3af Section 30.9.1.1.7
           aPSEInvalidSignatureCounter"
    ::= { pethPsePortEntry 11 }
        
   pethPsePortPowerDeniedCounter OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION
          "This counter is incremented when the PSE state diagram
             enters the state POWER_DENIED."
    REFERENCE
      "IEEE Std 802.3af Section 30.9.1.1.8
       aPSEPowerDeniedCounter"
    ::= { pethPsePortEntry 12 }
        
   pethPsePortOverLoadCounter OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION
          "This counter is incremented when the PSE state diagram
             enters the state ERROR_DELAY_OVER."
    REFERENCE
      "IEEE Std 802.3af Section 30.9.1.1.9
       aPSEOverLoadCounter"
    ::= { pethPsePortEntry 13 }
        
   pethPsePortShortCounter OBJECT-TYPE
    SYNTAX Counter32
    MAX-ACCESS read-only
    STATUS current
    DESCRIPTION
          "This counter is incremented when the PSE state diagram
             enters the state ERROR_DELAY_SHORT."
    REFERENCE
      "IEEE Std 802.3af Section 30.9.1.1.10
       aPSEShortCounter"
    ::= { pethPsePortEntry 14 }
        

-- Main PSE Objects

- メインPSEオブジェクト

pethMainPseObjects       OBJECT IDENTIFIER ::= { pethObjects 3 }
pethMainPseTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF PethMainPseEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table of objects that display and control attributes
            of the main power source in a PSE  device.  Ethernet
            switches are one example of boxes that would support
            these objects.
            Values of all read-write objects in this table are
            persistent at restart/reboot."
       ::= { pethMainPseObjects 1 }
        
   pethMainPseEntry OBJECT-TYPE
       SYNTAX      PethMainPseEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
            "A set of objects that display and control the Main
             power of a PSE. "
       INDEX    { pethMainPseGroupIndex }
       ::= { pethMainPseTable 1 }
        
   PethMainPseEntry ::= SEQUENCE {
       pethMainPseGroupIndex
           Integer32,
       pethMainPsePower
           Gauge32 ,
       pethMainPseOperStatus
           INTEGER,
       pethMainPseConsumptionPower
           Gauge32,
       pethMainPseUsageThreshold
           Integer32
   }
     pethMainPseGroupIndex OBJECT-TYPE
       SYNTAX       Integer32 (1..2147483647)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This variable uniquely identifies the group to which
           power Ethernet PSE is connected.  Group means (box in
           the stack, module in a rack) and the value 1 MUST be
           used for non-modular devices.  Furthermore, the same
           value MUST be used in this variable, pethPsePortGroupIndex,
           and pethNotificationControlGroupIndex to refer to a
           given box in a stack or module in a rack."
       ::= { pethMainPseEntry 1 }
        
     pethMainPsePower OBJECT-TYPE
       SYNTAX      Gauge32  (1..65535)
       UNITS      "Watts"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
               "The nominal power of the PSE expressed in Watts."
       ::= { pethMainPseEntry 2 }
        
     pethMainPseOperStatus OBJECT-TYPE
       SYNTAX INTEGER   {
               on(1),
               off(2),
               faulty(3)
          }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
               "The operational status of the main PSE."
       ::= { pethMainPseEntry 3 }
        
     pethMainPseConsumptionPower OBJECT-TYPE
       SYNTAX      Gauge32
       UNITS      "Watts"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
               "Measured usage power expressed in Watts."
       ::= { pethMainPseEntry 4 }
        
     pethMainPseUsageThreshold OBJECT-TYPE
       SYNTAX      Integer32  (1..99)
       UNITS      "%"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
               "The usage threshold expressed in percents for
                comparing the measured power and initiating
                an alarm if the threshold is exceeded."
       ::= { pethMainPseEntry 5 }
        

-- Notification Control Objects

- 通知制御オブジェクト

pethNotificationControl        OBJECT IDENTIFIER ::= { pethObjects 4 }
        
pethNotificationControlTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF PethNotificationControlEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table of objects that display and control the
            Notification on a PSE  device.
            Values of all read-write objects in this table are
            persistent at restart/reboot."
       ::= { pethNotificationControl 1 }
        
   pethNotificationControlEntry OBJECT-TYPE
       SYNTAX      PethNotificationControlEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
            "A set of objects that control the Notification events."
       INDEX    { pethNotificationControlGroupIndex }
       ::= { pethNotificationControlTable 1 }
        
   PethNotificationControlEntry ::= SEQUENCE {
       pethNotificationControlGroupIndex
           Integer32,
       pethNotificationControlEnable
           TruthValue
   }
     pethNotificationControlGroupIndex OBJECT-TYPE
       SYNTAX      Integer32 (1..2147483647)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "This variable uniquely identifies the group.  Group
            means box in the stack, module in a rack and the value
            1 MUST be used for non-modular devices.  Furthermore,
            the same value MUST be used in this variable,
            pethPsePortGroupIndex, and
            pethMainPseGroupIndex to refer to a given box in a
            stack or module in a rack. "
       ::= { pethNotificationControlEntry 1 }
        
      pethNotificationControlEnable  OBJECT-TYPE
       SYNTAX             TruthValue
       MAX-ACCESS         read-write
       STATUS             current
       DESCRIPTION
          "This object controls, on a per-group basis, whether
             or not notifications from the agent are enabled.  The
             value true(1) means that notifications are enabled; the
             value false(2) means that they are not."
       ::= { pethNotificationControlEntry 2 }
        

-- -- Notifications Section -- --

---通知セクション---

     pethPsePortOnOffNotification NOTIFICATION-TYPE
         OBJECTS     { pethPsePortDetectionStatus }
         STATUS      current
         DESCRIPTION
             " This Notification indicates if Pse Port is delivering or
               not power to the PD.  This Notification SHOULD be sent on
               every status change except in the searching mode.
               At least 500 msec must elapse between notifications
               being emitted by the same object instance."
          ::= { pethNotifications 1 }
        
     pethMainPowerUsageOnNotification NOTIFICATION-TYPE
         OBJECTS     { pethMainPseConsumptionPower  }
         STATUS      current
         DESCRIPTION
           " This Notification indicate PSE Threshold usage
               indication is on, the usage power is above the
               threshold.  At least 500 msec must elapse between
               notifications being emitted by the same object
               instance."
         ::= { pethNotifications 2 }
        
      pethMainPowerUsageOffNotification NOTIFICATION-TYPE
         OBJECTS     { pethMainPseConsumptionPower }
         STATUS      current
         DESCRIPTION
           " This Notification indicates PSE Threshold usage indication
               off, the usage power is below the threshold.
               At least 500 msec must elapse between notifications being
               emitted by the same object instance."
         ::= { pethNotifications 3 }
        
--
-- Conformance Section
--
pethCompliances OBJECT IDENTIFIER ::= { pethConformance 1 }
pethGroups      OBJECT IDENTIFIER ::= { pethConformance 2 }
        

pethCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Describes the requirements for conformance to the Power Ethernet MIB."

PethComplianceモジュールコンプライアンスステータス現在の説明「パワーイーサネットMIBへの適合の要件を説明しています。」

       MODULE  -- this module
           MANDATORY-GROUPS { pethPsePortGroup,
                              pethPsePortNotificationGroup,
                              pethNotificationControlGroup
                            }
           GROUP   pethMainPseGroup
           DESCRIPTION
               "The pethMainPseGroup is mandatory for PSE systems
                that implement a main power supply."
           GROUP   pethMainPowerNotificationGroup
           DESCRIPTION
               "The pethMainPowerNotificationGroup is mandatory for
               PSE systems that implement a main power supply."
       ::= { pethCompliances 1 }
        
pethPsePortGroup OBJECT-GROUP
    OBJECTS {
       pethPsePortAdminEnable,
       pethPsePortPowerPairsControlAbility,
       pethPsePortPowerPairs,
       pethPsePortDetectionStatus,
       pethPsePortPowerPriority,
       pethPsePortMPSAbsentCounter,
       pethPsePortInvalidSignatureCounter,
       pethPsePortPowerDeniedCounter,
       pethPsePortOverLoadCounter,
       pethPsePortShortCounter,
       pethPsePortType,
       pethPsePortPowerClassifications
    }
    STATUS  current
    DESCRIPTION
          "PSE Port objects."
    ::= { pethGroups 1 }
        
pethMainPseGroup OBJECT-GROUP
    OBJECTS {
       pethMainPsePower,
       pethMainPseOperStatus,
       pethMainPseConsumptionPower,
       pethMainPseUsageThreshold
    }
    STATUS  current
    DESCRIPTION
            "Main PSE Objects. "
    ::= { pethGroups 2 }
        

pethNotificationControlGroup OBJECT-GROUP

PethnotificationControlGroupオブジェクトグループ

    OBJECTS {
       pethNotificationControlEnable
    }
    STATUS  current
    DESCRIPTION
            "Notification Control  Objects. "
    ::= { pethGroups 3 }
        
pethPsePortNotificationGroup NOTIFICATION-GROUP
    NOTIFICATIONS { pethPsePortOnOffNotification}
    STATUS           current
    DESCRIPTION  "Pse Port Notifications."
    ::= { pethGroups 4 }
        
  pethMainPowerNotificationGroup NOTIFICATION-GROUP
     NOTIFICATIONS { pethMainPowerUsageOnNotification,
                      pethMainPowerUsageOffNotification}
    STATUS           current
    DESCRIPTION  "Main PSE Notifications."
      ::= { pethGroups 5 }
        

END

終わり

6. Acknowledgements
6. 謝辞

This document is the product of the Ethernet Interfaces and Hub MIB WG. The authors would like to recognize the special contributions of C.M. Heard and David Law.

このドキュメントは、イーサネットインターフェイスとハブMIB WGの製品です。著者は、C.M。の特別な貢献を認識したいと考えています。聞いたとデビッド・ロー。

7. References
7. 参考文献
7.1. Normative References
7.1. 引用文献

[RFC2026] Bradner, S., "The Internet Standards Process - Revision 3", BCP 9, RFC 2026, October 1996.

[RFC2026] Bradner、S。、「インターネット標準プロセス-Revision 3」、BCP 9、RFC 2026、1996年10月。

[RFC2578] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.

[RFC2578] McCloghrie、K.、Perkins、D。、およびJ. Schoenwaelder、「管理情報の構造バージョン2(SMIV2)」、STD 58、RFC 2578、1999年4月。

[RFC2579] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999.

[RFC2579] McCloghrie、K.、Perkins、D。、およびJ. Schoenwaelder、「SMIV2のテキストコンベンション」、STD 58、RFC 2579、1999年4月。

[RFC2580] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999.

[RFC2580] McCloghrie、K.、Perkins、D。およびJ. Schoenwaelder、「SMIV2の適合ステートメント」、STD 58、RFC 2580、1999年4月。

[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.

[RFC2119] Bradner、S。、「要件レベルを示すためにRFCで使用するためのキーワード」、BCP 14、RFC 2119、1997年3月。

[RFC3635] Flick, J., "Definitions of Managed Objects for the Ethernet-like Interface Types", RFC 3635, September 2003.

[RFC3635] Flick、J。、「イーサネットのようなインターフェイスタイプの管理オブジェクトの定義」、RFC 3635、2003年9月。

[RFC3411] Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", STD 62, RFC 3411, December 2002.

[RFC3411] Harrington、D.、Presuhn、R。、およびB. Wijnen、「単純なネットワーク管理プロトコル(SNMP)管理フレームワークを説明するためのアーキテクチャ」、STD 62、RFC 3411、2002年12月。

[IEEE-802.3af] IEEE 802.3 Working Group, "IEEE Std 802.3af-2003 - Data Terminal Equipment (DTE) Power via Media Dependent Interface (MDI)", July 2003.

[IEEE-802.3AF] IEEE 802.3ワーキンググループ、「IEEE STD 802.3AF-2003-メディア依存インターフェイス(MDI)を介したデータターミナル機器(DTE)電源」、2003年7月。

7.2. Informative References
7.2. 参考引用

[RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002.

[RFC3410] Case、J.、Mundy、R.、Partain、D。およびB. Stewart、「インターネット標準管理フレームワークの紹介と適用声明」、RFC 3410、2002年12月。

8. Intellectual Property Statement
8. 知的財産声明

The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat.

IETFは、知的財産またはその他の権利の有効性または範囲に関して、この文書に記載されているテクノロジーの実装または使用に関連すると主張される可能性のある他の権利、またはそのような権利に基づくライセンスがどの程度であるかについての程度に関連する可能性があるという立場はありません。利用可能;また、そのような権利を特定するために努力したことも表明していません。標準トラックおよび標準関連のドキュメントの権利に関するIETFの手順に関する情報は、BCP-11に記載されています。出版のために利用可能にされた権利の請求のコピーと、利用可能になるライセンスの保証、またはこの仕様の実装者またはユーザーによるそのような独自の権利の使用のための一般的なライセンスまたは許可を取得しようとする試みの結果を得ることができますIETF事務局から。

The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director.

IETFは、関心のある当事者に、この基準を実践するために必要な技術をカバーする可能性のある著作権、特許、または特許出願、またはその他の独自の権利を注意深く招待するよう招待しています。情報をIETFエグゼクティブディレクターに宛ててください。

9. Security Considerations
9. セキュリティに関する考慮事項

There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations.

このMIBモジュールには、読み取りワイトの最大アクセス句を持つ多くの管理オブジェクトが定義されています。このようなオブジェクトは、一部のネットワーク環境で敏感または脆弱と見なされる場合があります。適切な保護なしの非セキュア環境でのセット操作のサポートは、ネットワーク操作に悪影響を与える可能性があります。

Setting the following object to incorrect values can result in improper operation of the PSE, including the possibility that the PD does not receive power from the PSE port:

次のオブジェクトを誤った値に設定すると、PDがPSEポートから電力を受け取らない可能性を含め、PSEの不適切な動作につながる可能性があります。

pethPsePortAdminEnable pethPsePortPowerPairs pethPsePortPowerPriority pethPsePortType

pethpseportadminenable pethpseportpowerpairs pethpseportpowerpowerity pethpseporttype

Setting the following objects to incorrect values can result in an excessive number of traps being sent to network management stations:

次のオブジェクトを誤った値に設定すると、ネットワーク管理ステーションに送信されるトラップ数が過剰になります。

pethMainPseUsageThreshold pethNotificationControlEnable

pethmainpseusagethershold pethnotification controlenable

Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. These are:

このMIBモジュールの読み取り可能なオブジェクトのいくつか(つまり、アクセスできないこと以外に最大アクセスを備えたオブジェクト)は、一部のネットワーク環境で敏感または脆弱と見なされる場合があります。これらは:

pethPsePortPowerPairsControlAbility pethPsePortPowerPriority pethPsePortPowerClassifications

pethpseportpowerpairscontrolability pethpseportpowerproprity pethpseportpowerclassifications

It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt their values when sending them over the network via SNMP.

したがって、これらのオブジェクトへのアクセスを取得および/または通知することさえ制御し、SNMPを介してネットワーク上に送信するときに値を暗号化することも重要です。

SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.

SNMPV3以前のSNMPバージョンには、適切なセキュリティは含まれていませんでした。ネットワーク自体が(たとえばIPSECを使用して)安全である場合でも、それでもセキュアネットワークで誰がアクセスして取得/セット(読み取り/変更/作成/削除/削除)を制御することはできません。MIBモジュール。

It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy).

実装者は、SNMPV3暗号化メカニズム(認証とプライバシー用)の完全なサポートを含む、SNMPV3フレームワーク([RFC3410]、セクション8を参照)で提供されるセキュリティ機能を考慮することをお勧めします。

Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them.

さらに、SNMPV3より前のSNMPバージョンの展開は推奨されません。代わりに、SNMPV3を展開し、暗号化セキュリティを有効にすることをお勧めします。その場合、このMIBモジュールのインスタンスへのアクセスを提供するSNMPエンティティが、実際に取得または設定する正当な権利を持つプリンシパル(ユーザー)にのみオブジェクトにアクセスできるように適切に構成されていることを保証するのは、顧客/オペレーターの責任です(変更を変更します(変更)/作成/削除)それら。

10. Authors' Addresses
10. 著者のアドレス

Avi Berger PowerDsine Inc. 1, Hanagar St., P.O. Box 7220 Hod Hasharon 45421, Israel

Avi Berger Powerdsine Inc. 1、Hanagar St.、P.O。Box 7220 Hod Hasharon 45421、イスラエル

   Phone: +972-9-7755100 Ext 307
   Fax:   +972-9-7755120
   EMail: avib@PowerDsine.com
        

Dan Romascanu Avaya Atidim Technology Park, Bldg. #3 Tel Aviv, 61131 Israel

Dan Romascanu Avaya Atidim Technology Park、Bldg。#3テルアビブ、61131イスラエル

   Phone: +972-3-645-8414
   EMail: dromasca@avaya.com
        
11. 完全な著作権声明

Copyright (C) The Internet Society (2003). All Rights Reserved.

Copyright(c)The Internet Society(2003)。無断転載を禁じます。

This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English.

このドキュメントと翻訳は他の人にコピーされて提供される場合があります。また、それについてコメントまたは説明する派生作品、またはその実装を支援することは、いかなる種類の制限なしに、準備、コピー、公開、および部分的に配布される場合があります。、上記の著作権通知とこの段落がそのようなすべてのコピーとデリバティブ作品に含まれている場合。ただし、このドキュメント自体は、インターネット協会や他のインターネット組織への著作権通知や参照を削除するなど、いかなる方法でも変更できない場合があります。インターネット標準プロセスに従うか、英語以外の言語に翻訳するために必要な場合に従う必要があります。

The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assignees.

上記の限られた許可は永続的であり、インターネット社会やその後継者または譲受人によって取り消されることはありません。

This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

このドキュメントと本書に含まれる情報は、「現状」に基づいて提供されており、インターネット社会とインターネットエンジニアリングタスクフォースは、ここにある情報の使用が行われないという保証を含むがこれらに限定されないすべての保証を否認します。特定の目的に対する商品性または適合性の権利または黙示的な保証を侵害します。

Acknowledgement

謝辞

Funding for the RFC Editor function is currently provided by the Internet Society.

RFCエディター機能の資金は現在、インターネット協会によって提供されています。