[要約] 要約：RFC 4319は、HDSL2およびSHDSLラインの管理オブジェクトの定義に関するものであり、高ビットレートのDSL技術に関する情報を提供します。目的：このRFCの目的は、HDSL2およびSHDSLラインの管理オブジェクトの定義を提供し、これらの技術を使用するネットワークの管理と監視を支援することです。
Network Working Group C. Sikes
Request for Comments: 4319 Zhone Technologies, Inc.
Obsoletes: 3276 B. Ray
Category: Standards Track PESA Switching Systems, Inc.
R. Abbi
Alcatel USA
December 2005
Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line (SHDSL) Lines
ハイビットレートDSLの管理されたオブジェクトの定義-2番目の世代（HDSL2）およびシングルペア高速デジタルサブスクライバーライン（SHDSL）ライン
Status of This Memo
本文書の位置付け
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
このドキュメントは、インターネットコミュニティのインターネット標準トラックプロトコルを指定し、改善のための議論と提案を要求します。このプロトコルの標準化状態とステータスについては、「インターネット公式プロトコル標準」（STD 1）の現在のエディションを参照してください。このメモの配布は無制限です。
Copyright Notice
著作権表示
Copyright (C) The Internet Society (2005).
Copyright（c）The Internet Society（2005）。
Abstract
概要
This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community. In particular, it describes objects used for managing High Bit-Rate Digital Subscriber Line (DSL) - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line (SHDSL) interfaces. This document introduces extensions to several objects and textual conventions defined in HDSL2-SHDSL-Line MIB (RFC 3276). This document obsoletes RFC 3276.
このドキュメントでは、インターネットコミュニティのネットワーク管理プロトコルで使用する管理情報ベース（MIB）モジュールを定義しています。特に、高額のデジタルサブスクライバーライン（DSL） - 第2世代（HDSL2）およびシングルペア高速デジタルサブスクライバーライン（SHDSL）インターフェイスの管理に使用されるオブジェクトについて説明します。このドキュメントでは、hdsl2-shdsl-line mib（RFC 3276）で定義されたいくつかのオブジェクトとテキストの規則への拡張機能を紹介します。このドキュメントは、RFC 3276を廃止します。
Table of Contents
目次
1. The Internet-Standard Management Framework ......................2
2. Overview ........................................................2
2.1. Relationship to Other MIBs .................................3
2.1.1. General IF-MIB Integration (RFC 2863) ...............3
2.1.2. Usage of ifTable ....................................3
2.2. IANA Considerations ........................................4
2.3. Conventions Used in the MIB Module .........................5
2.3.1. Naming Conventions ..................................5
2.3.2. Textual Conventions .................................5
2.4. Structure ..................................................7
2.5. Line Topology ..............................................9
2.6. Counters, Interval Buckets, and Thresholds ................10
2.7. Profiles ..................................................11
2.8. Notifications .............................................12
3. Definitions ....................................................14
4. Implementation Analysis ........................................66
5. Security Considerations ........................................66
6. Acknowledgements ...............................................71
7. References .....................................................72
7.1. Normative References ......................................72
7.2. Informative References ....................................73
For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to Section 7 of RFC 3410 [RFC3410].
現在のインターネット標準管理フレームワークを説明するドキュメントの詳細な概要については、RFC 3410 [RFC3410]のセクション7を参照してください。
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580].
管理されたオブジェクトは、管理情報ベースまたはMIBと呼ばれる仮想情報ストアからアクセスされます。MIBオブジェクトは通常、単純なネットワーク管理プロトコル（SNMP）からアクセスされます。MIBのオブジェクトは、管理情報の構造（SMI）で定義されたメカニズムを使用して定義されます。このメモは、STD 58、RFC 2578 [RFC2578]、STD 58、RFC 2579 [RFC2579]およびSTD 58、RFC 2580 [RFC2580]に記載されているSMIV2に準拠したMIBモジュールを指定します。
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119].
この文書のキーワード "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", および "OPTIONAL" はRFC 2119 [RFC2119]で説明されているように解釈されます。
This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing HDSL2/SHDSL lines.
このドキュメントでは、HDSL2/SHDSLラインを管理する目的で、インターネットコミュニティのネットワーク管理プロトコルで使用する管理情報ベース（MIB）モジュールを定義します。
The MIB module described in RFC 3276 [RFC3276] describes objects used for managing High Bit-Rate DSL - 2nd generation (HDSL2) [T1E1.4] and Single-Pair High-Speed Digital Subscriber Line (SHDSL) interfaces [G.991.2]. These object descriptions are based upon the specifications for the HDSL2 and SHDSL Embedded Operations Channel (EOC), as defined in the American National Standards Institute (ANSI) T1E1.4/2000-006 [T1E1.4] and International Telecommunication Union (ITU) G.991.2 [G.991.2].
RFC 3276 [RFC3276]に記載されているMIBモジュールは、高ビットレートDSL-第2世代（HDSL2）[T1E1.4]およびシングルペア高速デジタルサブスクライバーライン（SHDSL）インターフェースの管理に使用されるオブジェクトを説明しています[G.991.2]。これらのオブジェクトの説明は、American National Standards Institute（ANSI）T1E1.4/2000-006 [T1E1.4]およびInternational Telecommunication Union（ITU）で定義されているHDSL2およびSHDSL埋め込み操作チャネル（EOC）の仕様に基づいています。G.991.2 [G.991.2]。
This document obsoletes RFC 3276 [RFC3276], which supports G.shdsl in that the MIB module described herein supports G.shdsl.bis as described in the G.991.2 [G.991.2]. In addition, objects have been added to improve the management of SHDSL lines.
このドキュメントは、RFC 3276 [RFC3276]を廃止します。これは、G.991.2 [G.991.2]で説明されているように、ここで説明するMIBモジュールがG.Shdsl.bisをサポートするという点でG.Shdslをサポートしています。さらに、SHDSLラインの管理を改善するためにオブジェクトが追加されています。
The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the MIB-2 Integration (RFC 2863 [RFC2863]) section of this document.
MIB-2統合（RFC 2863 [RFC2863]）セクションで説明されているように、MIBモジュールはMIB 2透過の下でMIBツリーにあります。
This section outlines the relationship of this MIB module with other MIB modules described in RFCs. Specifically, the IF-MIB, as presented in RFC 2863 [RFC2863], is discussed.
このセクションでは、このMIBモジュールとRFCSで説明されている他のMIBモジュールとの関係の概要を説明します。具体的には、RFC 2863 [RFC2863]に示されているIF-MIBについて説明します。
The HDSL2/SHDSL line MIB specifies the detailed attributes of a data interface. As such, it needs to integrate with RFC 2863 [RFC2863]. The IANA has assigned the following ifTypes to HDSL2 and SHDSL:
HDSL2/SHDSL Line MIBは、データインターフェイスの詳細な属性を指定します。そのため、RFC 2863 [RFC2863]と統合する必要があります。IANAは、次のIFTypesをHDSL2およびSHDSLに割り当てました。
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
hdsl2 (168), -- High Bit-Rate DSL, 2nd generation
shdsl (169), -- Multirate HDSL2
...
}
Note that the ifFixedLengthGroup from RFC 2863 [RFC2863] MUST be supported and that the ifRcvAddressGroup does not apply to this MIB module.
RFC 2863 [RFC2863]のiffixedlengthgroupをサポートする必要があり、ifrcvaddressgroupはこのMIBモジュールには適用されないことに注意してください。
The MIB branch identified by this ifType contains tables appropriate for this interface type. Most such tables extend the ifEntry table and are indexed by ifIndex. For interfaces in systems implementing this MIB module, those table entries indexed by ifIndex MUST be persistent.
このIFTypeで識別されたMIBブランチには、このインターフェイスタイプに適したテーブルが含まれています。このようなテーブルのほとんどは、Ifentryテーブルを拡張し、Ifindexによってインデックス化されています。このMIBモジュールを実装するシステムのインターフェイスの場合、ifindexによってインデックス付けされたテーブルエントリは永続的でなければなりません。
The following attributes are part of the mandatory ifGeneralInformationGroup in RFC 2863 [RFC2863] and are not duplicated in the HDSL2/SHDSL line MIB.
次の属性は、RFC 2863 [RFC2863]の必須のIfgeneralInformationGroupの一部であり、HDSL2/SHDSLラインMIBで複製されていません。
===================================================================
ifIndex Interface index.
Ifindexインターフェイスインデックス。
ifDescr See interfaces MIB [RFC2863].
ifdescrは、インターフェイスmib [rfc2863]を参照してください。
ifType hdsl2(168) or shdsl(169).
IFType HDSL2（168）またはSHDSL（169）。
ifSpeed Set as appropriate. (This is fixed at 1552000 for HDSL2 lines)
必要に応じて設定されています。（これはHDSL2行の1552000に固定されています）
ifPhysAddress This object MUST have an octet string with zero length.
ifphysAddressこのオブジェクトには、長さがゼロのオクテット文字列が必要です。
ifAdminStatus See interfaces MIB [RFC2863].
Ifadmintatusは、インターフェイスmib [rfc2863]を参照してください。
ifOperStatus See interfaces MIB [RFC2863].
ifoperstatusは、インターフェイスmib [rfc2863]を参照してください。
ifLastChange See interfaces MIB [RFC2863].
iflastchangeは、インターフェイスMIB [RFC2863]を参照してください。
ifName See interfaces MIB [RFC2863].
IFNameは、インターフェイスMIB [RFC2863]を参照してください。
ifAlias See interfaces MIB [RFC2863].
IfaliasはインターフェイスMIB [RFC2863]を参照してください。
ifLinkUpDownTrapEnable Default to enabled(1).
iflinkupdownTrapenableデフォルトは有効になります（1）。
ifHighSpeed Set as appropriate. (For HDSL2 lines, this is fixed at 2)
必要に応じてIFHighSpeedセット。（HDSL2行の場合、これは2に固定されています）
ifConnectorPresent Set as appropriate.
必要に応じて設定されたifconnectorPresent。
===================================================================
Figure 1: Use of ifTable Objects
The HDSL2-SHDSL-LINE-MIB module requires the allocation of a single object identifier for its MODULE-IDENTITY. The IANA has allocated this object identifier in the transmission subtree (48), defined in the SNMPv2-SMI MIB module.
HDSL2-SHDSL-LINE-MIBモジュールには、モジュール同一性に単一のオブジェクト識別子の割り当てが必要です。IANAは、snmpv2-smi mibモジュールで定義されているトランスミッションサブツリー（48）にこのオブジェクト識別子を割り当てています。
The assignment was in fact done when RFC 3276 was published, and this revision of the RFC does not require any new action from IANA.
実際には、RFC 3276が公開されたときに割り当てが行われ、RFCのこの改訂にはIANAからの新しいアクションは必要ありません。
A. xtuC refers to a central site terminal unit;
H2TU-C for HDSL2, or STU-C for SHDSL.
B. xtuR refers to a remote site terminal unit;
H2TU-R for HDSL2, or STU-R for SHDSL.
C. xtu refers to a terminal unit; either an xtuC or xtuR.
D. xru refer to a regenerator unit;
H2RU for HDSL2, or SRU for SHDSL.
E. xU refers to any HDSL2/SHDSL unit; either an xtu or xru.
F. CRC is Cyclic Redundancy Check [G.991.2].
G. ES means Errored Second [G.991.2].
J. LOSW means Loss of Sync Word [G.991.2].
I. LOSWS means LOSW Seconds [G.991.2].
J. SES means Severely Errored Second [G.991.2].
K. SNR means Signal-to-Noise Ratio [G.991.2].
L. UAS means Unavailable Second [G.991.2].
The following textual conventions are defined to reflect the line topology in the MIB module (further discussed in the following section) and to define the behavior of the statistics to be maintained by an agent.
次のテキスト規則は、MIBモジュールのライントポロジーを反映し（次のセクションでさらに説明します）、エージェントが維持する統計の動作を定義するために定義されています。
o Hdsl2ShdslUnitId:
o hdsl2shdslunitid：
Attributes with this syntax uniquely identify each unit in an HDSL2/SHDSL span. It mirrors the EOC addressing mechanism:
この構文の属性は、HDSL2/SHDSLスパンの各ユニットを一意に識別します。EOCアドレス指定メカニズムを反映しています。
xtuC(1) - central office (CO) terminal unit
xtuR(2) - customer premises equipment (CPE)
terminal unit
xru1(3) .. xru8(10) - regenerators, numbered from
central office side
o Hdsl2ShdslUnitSide:
o hdsl2shdslunitside：
Attributes with this syntax reference the two sides of a unit:
この構文の属性は、ユニットの両側を参照します。
networkSide(1) - N in figure 2, below
customerSide(2) - C in figure 2, below
o Hdsl2ShdslWirePair:
o hdsl2shdslwirepair：
Attributes with this syntax reference the wire pairs connecting the units:
この構文の属性は、ユニットを接続するワイヤペアを参照します。
wirePair1(1) - First pair for HDSL2/SHDSL. wirePair2(2) - Optional second pair for SHDSL only. wirePair3(3) - Optional third pair for SHDSL.bis only. wirePair4(4) - Optional fourth pair for SHDSL.bis only.
WirePair1（1） - HDSL2/SHDSLの最初のペア。WirePair2（2） - SHDSLのみのオプションの2番目のペア。wirepair3（3） - shdsl.bisのみのオプションの3番目のペア。wirepair4（4） - shdsl.bisのみのオプションの4番目のペア。
o Hdsl2ShdslTransmissionModeType:
o hdsl2shdsltransmissionModeType：
Attributes with this syntax specify the regional setting for an SHDSL line. Specified as a BITS construct, the two mode types are:
この構文の属性は、SHDSLラインの地域設定を指定します。ビットコンストラクトとして指定されている場合、2つのモードタイプは次のとおりです。
region1 - ITU-T G.991.2 Annex A region2 - ITU-T G.991.2 Annex B
リージョン1 -ITU -T G.991.2 Annex A Region2 -ITU -T G.991.2付録B
o Hdsl2ShdslPerfCurrDayCount:
o hdsl2shdslperfcurrdaycount：
Attributes with this syntax define the behavior of the 1-day (24 hour) gauges found in the MIB module.
この構文の属性は、MIBモジュールで見つかった1日（24時間）ゲージの動作を定義します。
o Hdsl2Shdsl1DayIntervalCount:
o hdsl2shdsl1dayintervalcount：
Attributes with this syntax define the behavior of the 1-day (24 hour) interval counters found in the MIB module.
この構文の属性は、MIBモジュールで見つかった1日（24時間）間隔カウンターの動作を定義します。
o Hdsl2ShdslPerfTimeElapsed:
o HDSL2SHDSLPERFTIMELAPSED：
Attributes with this syntax define the behavior of the elapsed time counters found in the MIB module.
この構文の属性は、MIBモジュールで見つかった経過時間カウンターの動作を定義します。
o Hdsl2ShdslPerfIntervalThreshold:
o HDSL2SHDSLPERFINTERVALTHRESHOLD：
Attributes with this syntax define the behavior of the alarm thresholds found in the MIB module.
この構文の属性は、MIBモジュールで見つかったアラームしきい値の動作を定義します。
o Hdsl2ShdslClockReferenceType:
o hdsl2shdslclockreferenceType：
Attributes with this syntax define the clock references for the HDSL2/SHDSL span.
この構文の属性は、HDSL2/SHDSLスパンのクロック参照を定義します。
The MIB module is structured into the following MIB groups:
MIBモジュールは、次のMIBグループに構成されています。
o Span Configuration Group:
o SPAN構成グループ：
This group supports MIB objects for configuring parameters for the HDSL2/SHDSL span. It contains the following table:
このグループは、HDSL2/SHDSLスパンのパラメーターを構成するためのMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2ShdslSpanConfTable
- hdsl2shdslspanconftable
o Span Status Group:
o スパンステータスグループ：
This group supports MIB objects for retrieving span status information. It contains the following table:
このグループは、SPANステータス情報を取得するためにMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2ShdslSpanStatusTable
- HDSL2SHDSLSPANSTATUSTABLE
o Unit Inventory Group:
o ユニットインベントリグループ：
This group supports MIB objects for retrieving unit inventory information about units in HDSL2/SHDSL lines via the EOC. It contains the following table:
このグループは、EOCを介してHDSL2/SHDSLラインのユニットに関するユニット在庫情報を取得するためのMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2ShdslInventoryTable
- HDSL2SHDSLINVENTORYTABLE
o Segment Endpoint Configuration Group:
o セグメントエンドポイント構成グループ：
This group supports MIB objects for configuring parameters for the HDSL2/SHDSL segment endpoints. It contains the following table:
このグループは、HDSL2/SHDSLセグメントエンドポイントのパラメーターを構成するためのMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2ShdslEndpointConfTable
- HDSL2SHDSLENDPOINTCONFTABLE
o Segment Endpoint Current Status/Performance Group:
o セグメントエンドポイント現在のステータス/パフォーマンスグループ：
This group supports MIB objects that provide the current status/ performance information relating to segment endpoints. It contains the following table:
このグループは、セグメントエンドポイントに関連する現在のステータス/パフォーマンス情報を提供するMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2ShdslEndpointCurrTable
- hdsl2shdslendpointcurrtable
o Segment Endpoint 15-Minute Interval Status/Performance Group:
o セグメントエンドポイント15分間隔ステータス/パフォーマンスグループ：
This group supports MIB objects that provide historic status/ performance information relating to segment endpoints in 15-minute intervals. It contains the following table:
このグループは、15分間隔でセグメントエンドポイントに関連する歴史的なステータス/パフォーマンス情報を提供するMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2Shdsl15MinIntervalTable
- HDSL2SHDSL15MININTERVALTABLE
o Segment Endpoint 1-Day Interval Status/Performance Group:
o セグメントエンドポイント1日間隔ステータス/パフォーマンスグループ：
This group supports MIB objects that provide historic status/ performance information relating to segment endpoints in 1-day intervals. It contains the following table:
このグループは、1日間隔でセグメントエンドポイントに関連する歴史的なステータス/パフォーマンス情報を提供するMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2Shdsl1DayIntervalTable
- hdsl2shdsl1dayintervaltable
o Maintenance Group:
o メンテナンスグループ：
This group supports MIB objects for performing maintenance operations such as loopbacks for HDSL2/SHDSL lines. It contains the following table(s):
このグループは、HDSL2/SHDSLラインのループバックなどのメンテナンス操作を実行するためのMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2ShdslEndpointMaintTable - hdsl2ShdslUnitMaintTable
- HDSL2SHDSLENDPOINTMAINTTABLE -HDSL2SHDSLUNITMAINTABLE
o Span Configuration Profile Group:
o SPAN構成プロファイルグループ：
This group supports MIB objects for defining configuration profiles for HDSL2/SHDSL spans. It contains the following table:
このグループは、HDSL2/SHDSLスパンの構成プロファイルを定義するためのMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2ShdslSpanConfProfileTable
- HDSL2SHDSLSPANCONFPROFILETABLE
o Segment Endpoint Alarm Configuration Profile Group:
o セグメントエンドポイントアラーム構成プロファイルグループ：
This group supports MIB objects for defining alarm configuration profiles for HDSL2/SHDSL segment endpoints. It contains the following table:
このグループは、HDSL2/SHDSLセグメントエンドポイントのアラーム構成プロファイルを定義するためのMIBオブジェクトをサポートしています。次の表が含まれています。
- hdsl2ShdslEndpointAlarmConfProfileTable
- HDSL2SHDSLENDPOINTALARMCONFPROFILETABLE
o Notifications Group:
o 通知グループ：
This group defines the notifications supported for HDSL2/SHDSL lines:
このグループは、HDSL2/SHDSL行でサポートされている通知を定義します。
- hdsl2ShdslLoopAttenCrossing - hdsl2ShdslSNRMarginCrossing - hdsl2ShdslPerfESThresh - hdsl2ShdslPerfSESThresh - hdsl2ShdslPerfCRCanomaliesThresh - hdsl2ShdslPerfLOSWSThresh - hdsl2ShdslPerfUASThresh - hdsl2ShdslSpanInvalidNumRepeaters - hdsl2ShdslLoopbackFailure - hdsl2ShdslpowerBackoff - hdsl2ShdsldeviceFault
- hdsl2ShdSlloopattencrossing -hdsl2shdslsnrmargincrossing -hdsl2shdslperfesthresh -hdsl2shdslperfsesthresh -hdsl2shdslperfcrcanomaliesthresh -hdsl2shdslploswssresh -hdslshresh -hdslshres dslspaninvalidnumrepeaterter -hdsl2shdslloopbackfailure -hdsl2shdslpowerbackoff -hdsl2shdsldevicefault
- hdsl2ShdsldcContinuityFault - hdsl2ShdslconfigInitFailure - hdsl2ShdslprotocolInitFailure - hdsl2ShdslnoNeighborPresent - hdsl2ShdslLocalPowerLoss
- HDSL2SHDSLDCCONTINUITYFAULT -HDSL2SHDSLCONFIGINITFAILURE -HDSL2SSLPROTOCOLINITFAILURE -HDSL2SHDSLNONEIGHBORPRESENT -HDSL2SHDSLSLLOCALPOWERLOSS
o SHDSL Wire Pair Group:
o shdslワイヤーペアグループ：
This group supports MIB objects that provide status of the SHDSL-specific wire pairs.
このグループは、SHDSL固有のワイヤペアのステータスを提供するMIBオブジェクトをサポートします。
- hdsl2ShdslEndpointCurrTipRingReversal - hdsl2ShdslEndpointCurrActivationState
- HDSL2SHDSLENDPOINTCURRTIPRINGREVERSERAL -HDSL2SHDSLENDPOINTCURRACTIVESTIVESTATE
o Payload Group:
o ペイロードグループ：
This group supports MIB objects for retrieving payload rates that exclude any framing overhead.
このグループは、フレーミングオーバーヘッドを除外するペイロードレートを取得するためのMIBオブジェクトをサポートしています。
- hdsl2ShdslStatusMaxAttainablePayloadRate - hdsl2ShdslStatusActualPayloadRate
- hdsl2shdslstatusmaxattainablepayloadrate -hdsl2sslstatusactualpayloadrate
An HDSL2/SHDSL line consists of a minimum of two units: xtuC (the central termination unit) and an xtuR (the remote termination unit). The line may optionally support up to 8 repeater/regenerator units (xru) as shown in the figure below.
HDSL2/SHDSLラインは、XTUC（中央ターミネーションユニット）とXTUR（リモート終了ユニット）の最低2つの単位で構成されています。下の図に示すように、このラインはオプションで最大8つのリピーター/再生ユニット（XRU）をサポートする場合があります。
<-- Network Side Customer Side -->
|</////////////////// HDSL2/SHDSL Span ////////////////////>|
<~~~> <~~~> HDSL2/SHDSL Segments <~~~>
+-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N +
+-------+ +-------+ +-------+ +-------+ +-------+
Key: <////> HDSL2/SHDSL span
<~~~~> HDSL2/SHDSL segment
=1= HDSL2/SHDSL wire-pair-1
=2= SHDSL optional wire-pair-2 (Not applicable to HDSL2)
C Customer side segment endpoint (modem)
N Network side segment endpoint (modem)
Figure 2: General Topology for an HDSL2/SHDSL Line
図2：HDSL2/SHDSLラインの一般的なトポロジー
For SNR Margin, Loop Attenuation, ES, SES, CRC anomalies, LOSW, and UAS, there are event counters, current 15-minute and 0 to 96 15- minute history bucket(s) of "interval-counters", as well as current and 0 to 30 previous 1-day interval-counter(s). Each current 15- minute event bucket has an associated threshold notification.
SNRマージン、ループ減衰、ES、SES、CRC異常、LOSW、およびUASには、イベントカウンター、現在の15分間、および0〜96 15分の履歴バケツの「インターバルカウンター」、および現在および0〜30の前の1日インターバルカウンター。現在の15分の各イベントバケットには、関連するしきい値通知があります。
Unlike RFC 3593 [RFC3593] and RFC 2662 [RFC2662], there is no representation in the MIB module for invalid buckets. In those cases where the data for an interval is suspect or known to be invalid, the agent MUST NOT report the interval. If the current 15-minute event bucket is determined to be invalid, notifications based upon the value of the event bucket MUST NOT be generated.
RFC 3593 [RFC3593]やRFC 2662 [RFC2662]とは異なり、無効なバケットのMIBモジュールには表現はありません。間隔のデータが疑わしい、または無効であると知られている場合、エージェントは間隔を報告してはなりません。現在の15分のイベントバケットが無効であると判断された場合、イベントバケットの値に基づく通知を生成する必要はありません。
Not reporting an interval will result in holes in the associated table. For example, the table hdsl2Shdsl15MinIntervalTable is indexed by { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide, hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}. If interval 12 is determined to be invalid but intervals 11 and 13 are valid, a Get Next operation on the indices .1.1.1.1.11 would return indices .1.1.1.1.13.
間隔を報告しないと、関連するテーブルに穴があります。たとえば、テーブルHDSL2SHDSL15MININTERVALTABLEは、{ifindex、hdsl2shdslinvindex、hdsl2shdslendpointside、hdsl2slendpointwirepair、hdsl2shdsl15minintervalnumber}によってインデックス付けされています。間隔12が無効であると判断されているが、間隔11と13が有効である場合、インデックスで次の操作を取得します。1.1.1.1.11はインデックス.1.1.1.1.13を返します。
There is no requirement for an agent to ensure a fixed relationship between the start of a 15-minute interval and any wall clock; however, some implementations may align the 15-minute intervals with quarter hours. Likewise, an implementation may choose to align 1-day intervals with the start of a day.
エージェントが15分間のインターバルの開始と壁の時計の間に固定関係を確保するための要件はありません。ただし、一部の実装では、15分間の間隔を4分の1時間に合わせる場合があります。同様に、実装では、1日間隔を1日の開始に合わせることを選択する場合があります。
Counters are not reset when an xU is reinitialized, only when the agent is reset or reinitialized (or under specific request outside the scope of this MIB module).
XUが再活性化されている場合、カウンターはリセットされません。エージェントがリセットまたは再活性化された場合にのみ（またはこのMIBモジュールの範囲外の特定の要求の下で）。
As a managed node can handle a large number of xUs (e.g., hundreds or perhaps thousands of lines), provisioning every parameter on every xU may become burdensome. Moreover, most lines are provisioned identically with the same set of parameters. To simplify the provisioning process, this MIB module makes use of profiles. A profile is a set of parameters that can be shared by multiple lines using the same configuration.
管理されたノードは、多数のXus（たとえば、数百または数千行など）を処理できるため、すべてのXuのすべてのパラメーターをプロビジョニングする可能性があります。さらに、ほとんどの行は、同じパラメーターセットで同じようにプロビジョニングされます。プロビジョニングプロセスを簡素化するために、このMIBモジュールはプロファイルを使用します。プロファイルは、同じ構成を使用して複数の行で共有できるパラメーターのセットです。
The following profiles are used in this MIB module:
このMIBモジュールでは、次のプロファイルが使用されています。
o Span Configuration Profiles - Span configuration profiles contain parameters for configuring HDSL2/SHDSL spans. They are defined in the hdsl2ShdslSpanConfProfileTable. Since span configuration parameters are only applicable for SHDSL, the support for span configuration profiles is optional for HDSL2 interfaces.
o SPAN構成プロファイル - SPAN構成プロファイルには、HDSL2/SHDSLスパンを構成するためのパラメーターが含まれています。それらは、hdsl2shdslspanconfprofiletableで定義されています。SPAN構成パラメーターはSHDSLにのみ適用できるため、SPAN構成プロファイルのサポートはHDSL2インターフェイスでオプションです。
Note that the configuration of the span dictates the behavior for each individual segment endpoint in the span. If a different configuration is provisioned for any given segment endpoint within the span, the new configuration for this segment endpoint will override the span configuration for this segment endpoint only.
スパンの構成は、スパンの個々のセグメントエンドポイントの動作を決定することに注意してください。スパン内の特定のセグメントエンドポイントに対して別の構成がプロビジョニングされている場合、このセグメントエンドポイントの新しい構成は、このセグメントエンドポイントのスパン構成のみをオーバーライドします。
o Segment Endpoint Alarm Configuration Profiles - These profiles contain parameters for configuring alarm thresholds for HDSL2/ SHDSL segment endpoints. These profiles are defined in the hdsl2ShdslEndpointAlarmConfProfileTable.
o セグメントエンドポイントアラーム構成プロファイル - これらのプロファイルには、HDSL2/ SHDSLセグメントエンドポイントのアラームしきい値を構成するためのパラメーターが含まれています。これらのプロファイルは、HDSL2SHDSLENDPOINTALARMCONFPROFILETABLEで定義されています。
The index value for this profile is a locally-unique administratively-assigned name for the profile having the textual convention 'SnmpAdminString' (RFC 3411 [RFC3411]).
このプロファイルのインデックス値は、テキストコンベンション「SNMPADMINSTRING」（RFC 3411 [RFC3411]）を持つプロファイルのローカルではない管理上割り当てされた名前です。
One or more lines may be configured to share parameters of a single profile (e.g., hdsl2ShdslEndpointAlarmConfProfile = 'silver') by setting its hdsl2ShdslEndpointAlarmConfProfile objects to the value of this profile. If a change is made to the profile, all lines that refer to it will be reconfigured to the changed parameters. Before a profile can be deleted or taken out of service, it must be first unreferenced from all associated lines.
HDSL2SHDSLENDLENDPOINTALARMCONFPROFILEオブジェクトをこのプロファイルの値に設定することにより、1つ以上の行を単一のプロファイルのパラメーター（例：HDSL2SHDSLENDSLENDPOINTALARMCONFPROFILE = 'SILVEL'）を共有するように構成できます。プロファイルに変更が加えられた場合、それを参照するすべての行は、変更されたパラメーターに再構成されます。プロファイルを削除したり、使用しなくなったりする前に、最初に関連するすべての行から参照されない必要があります。
Implementations MUST provide a default profile whose name is 'DEFVAL' for each profile type. The values of the associated parameters will be vendor specific unless otherwise indicated in this document. Before a line's profiles have been set, these profiles will be automatically used by setting hdsl2ShdslEndpointAlarmConfProfile and hdsl2ShdslSpanConfProfile to 'DEFVAL' where appropriate. This default profile name, 'DEFVAL', is considered reserved in the context of profiles defined in this MIB module.
実装は、各プロファイルタイプに対して「defval」という名前のデフォルトのプロファイルを提供する必要があります。関連するパラメーターの値は、このドキュメントで特に示されない限り、ベンダー固有のものになります。ラインのプロファイルが設定される前に、これらのプロファイルは、hdsl2shdslendpointalarmconfprofileとhdsl2shdslspanconfprofileを必要に応じて「defval」に設定することにより自動的に使用されます。このデフォルトのプロファイル名「defval」は、このMIBモジュールで定義されているプロファイルのコンテキストで予約されていると見なされます。
Profiles are created, assigned, and deleted dynamically using the profile name and profile row status in each of the four profile tables.
プロファイルは、4つのプロファイルテーブルのそれぞれにプロファイル名とプロファイルの行のステータスを使用して、動的に作成、割り当て、削除されます。
Profile changes MUST take effect immediately. These changes MAY result in a restart (hard reset or soft restart) of the units on the line.
プロファイルの変更はすぐに有効になる必要があります。これらの変更により、ライン上のユニットの再起動（ハードリセットまたはソフト再起動）が発生する場合があります。
The ability to generate the SNMP notifications coldStart/warmStart (per [RFC3418]), which are per agent (e.g., per Digital Subscriber Line Access Multiplexer, or DSLAM, in such a device), and linkUp/ linkDown (per [RFC2863]), which are per interface (i.e., HDSL2/SHDSL line) is required.
SNMP通知を生成する機能ColdStart/ Warmstart（[RFC3418]ごとに）、エージェントごと（例：そのようなデバイスでのデジタルサブスクライバーラインアクセスマルチプレクサ、DSLAMなど）、およびLinkup/ Linkdown（[RFC2863]ごと））、インターフェイスごと（つまり、HDSL2/SHDSLライン）が必要です。
A linkDown notification MAY be generated whenever any ES, SES, CRC anomaly, LOSW, or UAS event occurs. The corresponding linkUp notification MAY be sent when all link failure conditions are cleared.
ES、SES、CRC異常、LOSW、またはUASイベントが発生するたびに、リンクダウン通知が生成される場合があります。対応するリンクアップ通知は、すべてのリンク障害条件がクリアされたときに送信される場合があります。
The notifications defined in this MIB module are for initialization failure and for the threshold crossings associated with the following events: ES, SES, CRC anomaly, LOSW, and UAS. Each threshold has its own enable/threshold value. When that value is 0, the notification is disabled.
このMIBモジュールで定義されている通知は、初期化の障害および次のイベントに関連するしきい値交差のためのものです：ES、SES、CRC異常、LOSW、およびUAS。各しきい値には、独自の有効化/しきい値値があります。その値が0の場合、通知は無効になります。
The hdsl2ShdslEndpointCurrStatus is a bitmask representing all outstanding error conditions associated with a particular segment endpoint. Note that since the status of remote endpoints is obtained via the EOC, this information may be unavailable for units that are unreachable via EOC during a line error condition. Therefore, not all conditions may always be included in its current status. Notifications corresponding to the bit fields in this object are defined.
HDSL2SHDSLENDPOINTCURRSTATUSは、特定のセグメントエンドポイントに関連するすべての未解決のエラー条件を表すビットマスクです。リモートエンドポイントのステータスはEOCを介して取得されるため、この情報は、ラインエラー条件中にEOCを介して到達できないユニットでは利用できない場合があることに注意してください。したがって、すべての条件が常に現在のステータスに含まれるわけではありません。このオブジェクトのビットフィールドに対応する通知が定義されています。
Two alarm conditions, SNR Margin Alarm and Loop Attenuation Alarm, are organized in a manner slightly different from that implied in the EOC specifications. In the MIB module, these alarm conditions are tied to the two thresholds, hdsl2ShdslEndpointThreshSNRMargin and hdsl2ShdslEndpointThreshLoopAttenuation, found in the hdsl2ShdslEndpointAlarmConfProfileTable. In the EOC, the alarm conditions associated with these thresholds are per unit. In the MIB module, these alarm conditions are per endpoint. For terminal units, this has no impact. For repeaters, this implies an implementation variance where the agent in the terminal unit is responsible for detecting a threshold crossing. As the reporting of a repeater detected alarm condition to the polling terminal unit occurs in the same EOC message as the reporting of the current SNR Margin and Loop Attenuation values, it is anticipated that this will have very little impact on agent implementation.
SNRマージンアラームとループ減衰アラームの2つのアラーム条件は、EOC仕様で暗示されているものとわずかに異なる方法で編成されています。MIBモジュールでは、これらのアラーム条件は、HDSL2SHDSLENDPOPEARARMCONFOFILETABLEで見られるHDSL2SHDSLENDPPOINTTHRESHSNRMARGINおよびHDSL2STLENDPPONETHRESHLOOPATTENUATIONであるHDSL2SHDSLENDSLENDSLENDSRESHSNRMARGINとHDSL2SLENDSLENDSLENDPOPESTHRESHLOOPATTENUTESに結び付けられています。EOCでは、これらのしきい値に関連するアラーム条件は単位あたりです。MIBモジュールでは、これらのアラーム条件はエンドポイントごとです。ターミナルユニットの場合、これには影響がありません。リピーターの場合、これは、端子ユニットのエージェントがしきい値の交差を検出する責任がある実装の差異を意味します。リピーターのポーリング端末ユニットへのアラーム条件の報告が、現在のSNRマージンとループ減衰値の報告と同じEOCメッセージで発生するため、これはエージェントの実装にほとんど影響を与えないと予想されます。
A threshold notification occurs whenever the corresponding current 15-minute interval error counter becomes equal to, or exceeds, the threshold value. Only one notification SHOULD be sent per interval per interface. Since the current 15-minute counter is reset to 0 every 15 minutes, and if the condition persists, the notification may recur as often as every 15 minutes. For example, to get a notification whenever a "loss of" event occurs (but at most once every 15 minutes), set the corresponding threshold to 1. The agent will generate a notification when the event originally occurs.
しきい値通知は、対応する電流15分間隔エラーカウンターがしきい値に等しく、またはそれを超える場合に発生します。インターフェイスごとに間隔ごとに1つの通知を送信する必要があります。現在の15分間のカウンターは15分ごとに0にリセットされるため、条件が持続する場合、通知は15分ごとに頻繁に再発する可能性があります。たとえば、「」イベントが発生するときはいつでも通知を取得するには（ただし、最大で15分ごとに1回）、対応するしきい値を1に設定します。エージェントは、イベントが最初に発生したときに通知を生成します。
Notifications, other than the threshold notifications listed above, SHOULD be rate limited (throttled) such that there is at least a 1-minute gap between the generation of consecutive notifications of the same event. When notifications are rate limited, they are dropped and not queued for sending at a future time. This is intended to be a general rate-limiting statement for notifications that have no explicit rate-limiting assertions in this document otherwise.
通知は、上記のしきい値通知を除いて、同じイベントの連続通知の生成の間に少なくとも1分のギャップがあるように、レート制限（スロットル）する必要があります。通知が制限されている場合、それらは削除され、将来の時間に送信するためにキューに留められません。これは、このドキュメントに明示的な料金制限アサーションを持たない通知の一般的な料金制限ステートメントであることを目的としています。
Note that the Network Management System, or NMS, may receive a linkDown notification as well, if enabled (via ifLinkUpDownTrapEnable [RFC2863]). At the beginning of the next 15-minute interval, the counter is reset. When the first second goes by and the event occurs, the current interval bucket will be 1, which equals the threshold, and the notification will be sent again.
ネットワーク管理システム（NMS）は、有効になっている場合（iflinkupdownTrapenable [rfc2863]）、リンクダウン通知も受信する場合があることに注意してください。次の15分間隔の開始時に、カウンターはリセットされます。最初の秒が経過してイベントが発生すると、現在のインターバルバケットが1になり、これはしきい値に等しくなり、通知は再度送信されます。
An hdsl2ShdslSpanInvalidNumRepeaters notification may be generated following completion of the discovery phase if the number of repeaters discovered on the line differs from the number of repeaters specified in hdsl2ShdslSpanConfNumRepeaters. For those conditions where the number of provisioned repeaters is greater than those encountered during span discovery, all table entries associated with the nonexistent repeaters are to be discarded. For those conditions where the number of provisioned repeaters is less than those encountered during span discovery, additional table entries are to be created using the default span configuration profile.
HDSL2SHDSLSPANINVALIDNUMREPEATERS通知は、発見フェーズの完了後に生成され、ラインで発見されたリピーターの数がHDSL2SHDSLSPANCONFNUMREPEATERETESで指定されたリピーターの数とは異なります。プロビジョニングされたリピーターの数がスパン発見中に遭遇した条件よりも大きい条件では、存在しないリピーターに関連するすべてのテーブルエントリが廃棄されます。プロビジョニングされたリピーターの数がスパン発見中に遭遇した条件よりも少ない条件では、デフォルトのスパン構成プロファイルを使用して追加のテーブルエントリを作成します。
HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Unsigned32, Gauge32, NOTIFICATION-TYPE, Integer32, transmission FROM SNMPv2-SMI RowStatus, TEXTUAL-CONVENTION FROM SNMPv2-TC ifIndex FROM IF-MIB PerfCurrentCount, PerfIntervalCount FROM PerfHist-TC-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF;
インポートモジュールアイデンティティ、オブジェクトタイプ、カウンター32、unsigned32、ゲージ32、通知タイプ、integer32、integer32、snmpv2-smi rowstatusからの伝送、if-mib perfcurrentcountからのsnmpv2-tc ifindexからのテキストコンベンション、perfhist-tc-mist-mist-mist-mist-tc-mist-mist-mist-mist-tc-mist-tc-mist-mist-mist-tc-mist-tc-mivSNMP-FrameWork-MIB Module Compliance、Object-Group、SNMPV2-CONFからの通知グループから。
hdsl2ShdslMIB MODULE-IDENTITY LAST-UPDATED "200512070000Z" -- December 7, 2005 ORGANIZATION "ADSLMIB Working Group" CONTACT-INFO "WG-email: adslmib@ietf.org WG-URL: http://www.ietf.org/html.charters/adslmib-charter.html Info: https://www1.ietf.org/mailman/listinfo/adslmib Chair: Mike Sneed Sand Channel Systems Postal: 1210-203 Westview Ln Raleigh NC 27605 USA Email: sneedmike@hotmail.com Phone: +1 206 600 7022
HDSL2SHDSLMIBモジュールIDULE-IDULE LATS-UPDATED "200512070000Z" - 2005年12月7日「ADSLMIBワーキンググループ」WG-EMAIL：adslmib@ietf.org WG-url：http：//www.ietf.org/html.Charters/adslmib-charter.html情報：https：//www1.ietf.org/mailman/listinfo/adslmib椅子：マイクスニードサンドチャネルシステム郵便郵便郵便局：1210-203電話：1 206 600 7022
Co-Chair Bob Ray PESA Switching Systems, Inc.
共同議長のボブ・レイ・ペサ・スイッチング・システム、Inc。
Postal 330-A Wynn Drive Huntsville, AL 35805 USA Phone +1 256 726 9200 ext. 142
Postal 330-A Wynn Drive Huntsville、AL 35805 USA Phone 1 256 726 9200 Ext。142
Co-editor: Clay Sikes Zhone Technologies, Inc. Postal: 8545 126th Ave. N. Largo, FL 33772 USA Email: csikes@zhone.com Phone: +1 727 530 8257
共同編集者：Clay Sikes Zhone Technologies、Inc。Postal：8545 126th Ave. N. Largo、FL 33772 USAメール：csikes@zhone.com電話：1 727 530 8257
Co-editor: Bob Ray PESA Switching Systems, Inc. Postal: 330-A Wynn Drive Huntsville, AL 35805 USA Email: rray@pesa.com Phone: +1 256 726 9200 ext. 142
共同編集者：Bob Ray Pesa Switching Systems、Inc。Postal：330-A Wynn Drive Huntsville、AL 35805 USA Email：rray@pesa.com電話：1 256 726 9200 Ext。142
Co-editor: Rajesh Abbi Alcatel USA Postal: 2301 Sugar Bush Road Raleigh, NC 27612-3339 USA
共同編集者：Rajesh Abbi Alcatel USA Postal：2301 Sugar Bush Road Raleigh、NC 27612-3339 USA
Email: Rajesh.Abbi@alcatel.com
Phone: +1 919 850 6194"
DESCRIPTION "This MIB module defines a collection of objects for managing HDSL2/SHDSL lines. An agent may reside at either end of the line; however, the MIB module is designed to require no management communication between the modems beyond that inherent in the low-level EOC line protocol as defined in ANSI T1E1.4/2000-006 (for HDSL2 lines) or in ITU G.991.2 (for SHDSL lines).
説明 "このMIBモジュールは、HDSL2/SHDSLラインを管理するためのオブジェクトのコレクションを定義します。エージェントは、ラインの両端に存在する場合があります。ただし、MIBモジュールは、低いものに固有のものを超えるモデム間の管理通信を必要としないように設計されています。ANSI T1E1.4/2000-006（HDSL2ライン用）またはITU G.991.2（SHDSLライン用）で定義されているレベルEOCラインプロトコル。
Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 4319; see the RFC itself for full legal notices."
Copyright（c）The Internet Society（2005）。このMIBモジュールのこのバージョンは、RFC 4319の一部です。完全な法的通知については、RFC自体を参照してください。」
REVISION "200512070000Z" -- December 7, 2005 DESCRIPTION "This version, published as RFC 4319. The following changes have been made in this version: 1. Added a 3rd and 4th wire pair. 2. Modified all rates such that their rates are only constrained by an unsigned 32-bit value and not by what today's perceived technology limitations are.
リビジョン「200512070000Z」 - 2005年12月7日説明「RFC 4319として公開されたこのバージョンの説明。このバージョンで次の変更が行われました。1。3番目と4番目のワイヤペアを追加しました。署名されていない32ビット値によってのみ制約され、今日の認識されているテクノロジーの制限が何であるかによっては制約されていません。
3. Clarified that the rates from RFC 3276 include payload and any applicable framing and added objects for payload-only rates. 4. Added an object to indicate whether the tip and ring are reversed on a wire pair. 5. Added an object to display the activation state of a wire pair. 6. Added references as necessary for clarification. 7. Added display hints to textual conventions as necessary. 8. Updated conformance statements as necessary. 9. Some changes were due to IETF requirements and RFC generation tools."
3. RFC 3276からのレートには、ペイロードと、該当するフレーミングおよびペイロードのみの料金の追加オブジェクトが含まれていることを明らかにしました。4.先端とリングがワイヤペアで逆になっているかどうかを示すオブジェクトを追加しました。5.ワイヤーペアのアクティベーション状態を表示するオブジェクトを追加しました。6.明確化に必要な参照を追加しました。7.必要に応じて、テキストの慣習にディスプレイのヒントを追加しました。8.必要に応じて、適合ステートメントを更新しました。9.いくつかの変更は、IETF要件とRFC生成ツールによるものでした。」
REVISION "200205090000Z" -- May 9, 2002 DESCRIPTION "Initial version, published as RFC 3276."
リビジョン「200205090000Z」 - 2002年5月9日説明「RFC 3276として公開された初期バージョン。」
::= { transmission 48 }
hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }
-- Textual Conventions used in this MIB module --
- このMIBモジュールで使用されているテキスト規則 -
Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A gauge associated with interface performance measurements in
a current 1-day (24 hour) measurement interval.
The value of this gauge starts at zero at the beginning of an interval and is increased when associated events occur, until the end of the 1-day interval. At that time, the value of the gauge is stored in the previous 1-day history interval, as defined in a companion object of type Hdsl2Shdsl1DayIntevalCount, and the current interval gauge is restarted at zero.
このゲージの値は、間隔の開始時にゼロから始まり、1日間の間隔の終了まで、関連するイベントが発生すると増加します。当時、ゲージの値は、HDSL2SHDSL1DAYINTEVALCOUNTタイプのコンパニオンオブジェクトで定義されているように、前の1日間の履歴間隔に保存され、現在の間隔ゲージがゼロで再起動されます。
In the case where the agent has no valid data available for this interval, the corresponding object instance is not available, and upon a retrieval request, a corresponding error message shall be returned to indicate that this instance does not exist. Please note that zero is a valid value." SYNTAX Gauge32
エージェントがこの間隔で利用可能な有効なデータを持っていない場合、対応するオブジェクトインスタンスは使用できません。また、検索要求に応じて、対応するエラーメッセージを返して、このインスタンスが存在しないことを示します。ゼロは有効な値であることに注意してください。 "Syntax Gauge32
Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"A counter associated with interface performance measurements
during the most previous 1-day (24 hour) measurement interval.
The value of this gauge is equal to the value of the current
day gauge, as defined in a companion object of type
Hdsl2ShdslPerfCurrDayCount, at the end of its most recent
interval.
In the case where the agent has no valid data available for this interval, the corresponding object instance is not available, and upon a retrieval request, a corresponding error message shall be returned to indicate that this instance does not exist." SYNTAX Gauge32
エージェントがこの間隔で使用可能な有効なデータがない場合、対応するオブジェクトインスタンスは使用できず、検索要求に応じて、対応するエラーメッセージを返して、このインスタンスが存在しないことを示します。
Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock or the addition
of a leap second, the current interval exceeds the maximum
value, the agent will return the maximum value.
For 15-minute intervals, the range is limited to (0..899). For 24-hour intervals, the range is limited to (0..86399)." SYNTAX Unsigned32(0..86399)
15分間の間、範囲は（0..899）に制限されています。24時間間隔で、範囲は（0..86399）に制限されています。
Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION
DISPLAY-HINT "d"
STATUS current
DESCRIPTION
"This convention defines a range of values that may be set in
a fault threshold alarm control. As the number of seconds in
a 15-minute interval numbers at most 900, objects of this type
may have a range of 0...900, where the value of 0 disables the
alarm."
SYNTAX Unsigned32(0..900)
Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the unique identification for all units in an
HDSL2/SHDSL span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
SYNTAX INTEGER
{
xtuC(1),
xtuR(2),
xru1(3),
xru2(4),
xru3(5),
xru4(6),
xru5(7),
xru6(8),
xru7(9),
xru8(10)
}
Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced side of an HDSL2/SHDSL unit - Network
or Customer side. The side facing the Network is the Network
side, while the side facing the Customer is the Customer side."
SYNTAX INTEGER
{
networkSide(1),
customerSide(2)
}
Hdsl2ShdslWirePair ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced pair of wires in an HDSL2/SHDSL segment.
HDSL2 only supports a single pair (wirePair1 or two wire),
SHDSL lines support an optional second pair (wirePair2 or four
wire), and G.shdsl.bis support an optional third pair
(wirePair3 or six wire) and an optional fourth pair
(wirePair4 or eight wire)."
SYNTAX INTEGER
{
wirePair1(1), -- two wire
wirePair2(2), -- four wire
wirePair3(3), -- six wire
wirePair4(4) -- eight wire
}
Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Contains the regional setting of the HDSL2/SHDSL span,
represented as a bit-map of possible settings. The various
bit positions are as follows:
Bit Meaning Description
1 region 1 Indicates ITU-T G.991.2 Annex A.
2 region 2 Indicates ITU-T G.991.2 Annex B."
SYNTAX BITS
{
region1(0),
region2(1)
}
Hdsl2ShdslClockReferenceType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The various STU-C symbol clock references for the
HDSL2/SHDSL span, represented as an enumeration."
SYNTAX INTEGER
{
localClk(1), -- Mode-1 per G991.2
networkClk(2), -- Mode-2 per G991.2
dataOrNetworkClk(3), -- Mode-3a per G991.2
dataClk(4) -- Mode-3b per G991.2
}
-- Span Configuration Group --
- スパン構成グループ -
hdsl2ShdslSpanConfTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry MAX-ACCESS not-accessible STATUS current
HDSL2SHDSLSPANGONFTABLEオブジェクトタイプの構文シーケンスHDSL2SHDSLSPANCONFENTRY MAX-ACCESS NOT-ACCESSABLEステータス電流
DESCRIPTION
"This table supports overall configuration of HDSL2/SHDSL
spans. Entries in this table MUST be maintained in a
persistent manner."
::= { hdsl2ShdslMibObjects 1 }
hdsl2ShdslSpanConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanConfTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanConfTable 1 }
Hdsl2ShdslSpanConfEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfNumRepeaters Unsigned32,
hdsl2ShdslSpanConfProfile SnmpAdminString,
hdsl2ShdslSpanConfAlarmProfile SnmpAdminString
}
hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
UNITS "repeaters"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object provisions the number of repeaters/regenerators
in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanConfEntry 1 }
hdsl2ShdslSpanConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is a pointer to a span configuration profile in the hdsl2ShdslSpanConfProfileTable, which applies to this span. The value of this object is the index of the referenced profile in the hdsl2ShdslSpanConfProfileTable. Note that span configuration profiles are only applicable to SHDSL lines.
HDSL2SHDSLSPANCONFPROFILEオブジェクトタイプの構文SNMPADMINSTRING（サイズ（1..32））Max-Access Read-Writeステータス現在の説明 "このオブジェクトは、HDSL2SHDSLSPANCONFPROFILETABLEのSPAN構成プロファイルへのポインターです。HDSL2SHDSLSPANCONFPROFILETABLEの参照プロファイルのインデックスです。SPAN構成プロファイルはSHDSLラインにのみ適用できることに注意してください。
HDSL2 lines MUST reference the default profile, 'DEFVAL'. By default, this object will have the value 'DEFVAL' (the index of the default profile).
HDSL2行は、デフォルトのプロファイル「defval」を参照する必要があります。デフォルトでは、このオブジェクトには値「defval」（デフォルトプロファイルのインデックス）があります。
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslSpanConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 2 }
hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is a pointer to an alarm configuration profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold configuration in the referenced profile will be used by default for all segment endpoints in this span. Individual endpoints may override this profile by explicitly specifying some other profile in the hdsl2ShdslEndpointConfTable. By default, this object will have the value 'DEFVAL' (the index of the default profile).
hdsl2Shdslspanconfalarmprofile object-type sntax snmpadminstring（size（1..32））max-access read-writeステータス現在の説明 "このオブジェクトは、hdsl2shdslendpointalarmconfofiletableのhdsl2shdslendpointalarmconforetableのアラーム構成プロファイルへのポインターです。HDSL2SHDSLENDPOINTALARMCONFPROFILETABLEのプロファイル。参照プロファイルのアラームしきい値構成は、このスパンのすべてのセグメントエンドポイントでデフォルトで使用されます。値「defval」（デフォルトプロファイルのインデックス）。
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 3 }
-- Span Status Group --
- スパンステータスグループ -
hdsl2ShdslSpanStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides overall status information of
HDSL2/SHDSL spans. This table contains live data from
equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 2 }
hdsl2ShdslSpanStatusEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanStatusTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanStatusTable 1 }
Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE
{
hdsl2ShdslStatusNumAvailRepeaters Unsigned32,
hdsl2ShdslStatusMaxAttainableLineRate Unsigned32,
hdsl2ShdslStatusActualLineRate Unsigned32,
hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslStatusMaxAttainablePayloadRate Unsigned32,
hdsl2ShdslStatusActualPayloadRate Unsigned32
}
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 1 }
hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the maximum attainable line rate in this HDSL2/SHDSL
span. This object provides the maximum rate the line is
capable of achieving. This is based upon measurements made
during line probing. This rate includes payload (user data)
and any applicable framing overhead."
::= { hdsl2ShdslSpanStatusEntry 2 }
hdsl2ShdslStatusActualLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span. This
SHOULD equal ifSpeed. This rate includes payload (user data)
and any applicable framing overhead"
::= { hdsl2ShdslSpanStatusEntry 3 }
hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current Power Spectral Density (PSD) regional
setting of the HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 4 }
hdsl2ShdslStatusMaxAttainablePayloadRate OBJECT-TYPE SYNTAX Unsigned32(0..4294967295) UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION
HDSL2SHDSLSTATUSMAXATAINABLEPAYLOADRATE OBJECT-TYPE SYNTAX UNSIGNED32（0..4294967295）ユニット「BPS」MAX-ACCESS READ-ONLYステータス現在の説明
"Contains the maximum attainable payload (user data)
line rate in this HDSL2/SHDSL span. This object provides
the maximum rate the line is capable of achieving. This
is based upon measurements made during line probing. Any
framing overhead is not included."
::= { hdsl2ShdslSpanStatusEntry 5 }
hdsl2ShdslStatusActualPayloadRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span. Any
framing overhead is not included."
::= { hdsl2ShdslSpanStatusEntry 6 }
-- Unit Inventory Group --
- ユニットインベントリグループ -
hdsl2ShdslInventoryTable OBJECT-TYPE SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table supports retrieval of unit inventory information available via the EOC from units in an HDSL2/SHDSL line.
HDSL2SHDSLINENVENTORYTABLEオブジェクトタイプの構文シーケンスHDSL2SHDSLINVENTORYENTRY MAX-ACCESS NOT-ACCESSABLEステータス現在の説明 "このテーブルは、HDSL2/SHDSLラインのユニットからEOCを介して利用可能なユニットインベントリ情報の取得をサポートします。
Entries in this table are dynamically created during the line discovery process. The life cycle for these entries is as follows:
この表のエントリは、ライン発見プロセス中に動的に作成されます。これらのエントリのライフサイクルは次のとおりです。
- xtu discovers a device, either a far-end xtu or an xru - an inventory table entry is created for the device - the line goes down for whatever reason - inventory table entries for unreachable devices are destroyed
- XTUは、ファーエンドXTUまたはXRUのいずれかのデバイスを発見します - デバイス用のインベントリテーブルエントリが作成されます - 何らかの理由でラインがダウンします - 到達不可能なデバイスの在庫テーブルエントリは破壊されます
As these entries are created/destroyed dynamically, they
are NOT persistent."
::= { hdsl2ShdslMibObjects 3 }
hdsl2ShdslInventoryEntry OBJECT-TYPE SYNTAX Hdsl2ShdslInventoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the hdsl2ShdslInventoryTable. Each entry
HDSL2SHDSLINVENTORYENTRYオブジェクトタイプ構文HDSL2SHDSLINVENTORYENTRY MAX-ACCESS NOT-ACCESSABLEステータス現在の説明 "HDSL2SHDSLINVENTORYTABLEのエントリ。各エントリ
represents inventory information for a single unit in an
HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslInventoryTable 1 }
Hdsl2ShdslInventoryEntry ::=
SEQUENCE
{
hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
hdsl2ShdslInvVendorID OCTET STRING,
hdsl2ShdslInvVendorModelNumber OCTET STRING,
hdsl2ShdslInvVendorSerialNumber OCTET STRING,
hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
hdsl2ShdslInvStandardVersion Integer32,
hdsl2ShdslInvVendorListNumber OCTET STRING,
hdsl2ShdslInvVendorIssueNumber OCTET STRING,
hdsl2ShdslInvVendorSoftwareVersion OCTET STRING,
hdsl2ShdslInvEquipmentCode OCTET STRING,
hdsl2ShdslInvVendorOther OCTET STRING,
hdsl2ShdslInvTransmissionModeCapability
Hdsl2ShdslTransmissionModeType
}
hdsl2ShdslInvIndex OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table corresponds to a physical element
in an HDSL2/SHDSL span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
::= { hdsl2ShdslInventoryEntry 1 }
hdsl2ShdslInvVendorID OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor ID as reported in an Inventory Response message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 25-32."
::= { hdsl2ShdslInventoryEntry 2 }
hdsl2ShdslInvVendorModelNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor model number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 33-44."
::= { hdsl2ShdslInventoryEntry 3 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor serial number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 45-56."
::= { hdsl2ShdslInventoryEntry 4 }
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor EOC version as reported in a Discovery Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.2, Discovery response - Message ID
129, Octet 12."
::= { hdsl2ShdslInventoryEntry 5 }
hdsl2ShdslInvStandardVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the HDSL2/SHDSL standard implemented, as reported
in an Inventory Response message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octet 2."
::= { hdsl2ShdslInventoryEntry 6 }
hdsl2ShdslInvVendorListNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(3))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor list number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 3-5."
::= { hdsl2ShdslInventoryEntry 7 }
hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor issue number as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 6-7."
::= { hdsl2ShdslInventoryEntry 8 }
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor software version as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 8-13."
::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(10))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 14-23."
::= { hdsl2ShdslInventoryEntry 10 }
hdsl2ShdslInvVendorOther OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Other vendor information as reported in an Inventory Response
message."
REFERENCE
"G.991.2, Section 9.5.5.7.4, Inventory response - Message ID
130, Octets 57-68."
::= { hdsl2ShdslInventoryEntry 11 }
hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the transmission mode capability of the SHDSL unit."
::= { hdsl2ShdslInventoryEntry 12 }
-- Segment Endpoint Configuration Group --
- セグメントエンドポイント構成グループ -
hdsl2ShdslEndpointConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports configuration parameters for segment
endpoints in an HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 4 }
hdsl2ShdslEndpointConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in an HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the
UnitId of the associated unit, the side of the unit, and the
wire pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointConfTable 1 }
Hdsl2ShdslEndpointConfEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide,
hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair,
hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString
}
hdsl2ShdslEndpointSide OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitSide
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The side of the unit associated with this segment endpoint --
Network/Customer side -- as per the Hdsl2ShdslUnitSide textual
convention."
::= { hdsl2ShdslEndpointConfEntry 1 }
hdsl2ShdslEndpointWirePair OBJECT-TYPE
SYNTAX Hdsl2ShdslWirePair
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The wire pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention."
::= { hdsl2ShdslEndpointConfEntry 2 }
hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "This object configures the alarm threshold values to be used for this segment endpoint. The values are obtained from the alarm configuration profile referenced by this object. The value of this object is the index of the referenced profile in the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero-length SnmpAdminString). If the value is a zero-length SnmpAdminString, the endpoint uses the default Alarm Configuration Profile for the associated span as per the hdsl2ShdslSpanConfAlarmProfile object in the hdsl2ShdslSpanConfTable. The default value of this object is a zero-length SnmpAdminString.
HDSL2SHDSLENDPOINTALARMCONFPROFILEオブジェクトタイプの構文SNMPADMINSTRING（サイズ（0..32））最大アクセスREAD-WRITEステータス現在の説明 "このオブジェクトは、このセグメントエンドポイントに使用するアラームしきい値値を構成します。このオブジェクトによって。このオブジェクトの値は、HDSL2SHDSLENDPOINTALARMCONFPROFILETABLEの参照プロファイルのインデックスまたはnull（ゼロ長SNMPADMINSTRING）です。値がゼロ長SNMPADMINSTRINGの場合、エンドポイントはエンドポイントがデフォルトアラーム構成プロファイルを使用します。HDSL2SHDSLSPANCONFTABALTのHDSL2SHDSLSPANSPANCONFALARMPROFILEオブジェクトによる関連スパン。このオブジェクトのデフォルト値は、ゼロ長SNMPADMINSTRINGです。
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslEndpointConfEntry 3 }
-- Segment Endpoint Current Status/Performance Group
--
hdsl2ShdslEndpointCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL lines. As with other
tables in this MIB module indexed by ifIndex, entries in this
table MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 5 }
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associated unit, the side
of the unit, and the wire pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair }
::= { hdsl2ShdslEndpointCurrTable 1 }
Hdsl2ShdslEndpointCurrEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointCurrAtn Integer32,
hdsl2ShdslEndpointCurrSnrMgn Integer32,
hdsl2ShdslEndpointCurrStatus BITS,
hdsl2ShdslEndpointES Counter32,
hdsl2ShdslEndpointSES Counter32,
hdsl2ShdslEndpointCRCanomalies Counter32,
hdsl2ShdslEndpointLOSWS Counter32,
hdsl2ShdslEndpointUAS Counter32,
hdsl2ShdslEndpointCurr15MinTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr15MinES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount,
hdsl2ShdslEndpointCurr1DayTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr1DayES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DaySES
Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurr1DayCRCanomalies Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurr1DayLOSWS Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurr1DayUAS Hdsl2ShdslPerfCurrDayCount, hdsl2ShdslEndpointCurrTipRingReversal INTEGER, hdsl2ShdslEndpointCurrActivationState INTEGER }
hdsl2shdslperfcurrdaycount、hdsl2shdslendpointcurr1daycrcanomalies hdsl2shdslperfcurrperfcurncount、hdsl2shdslendpointcurr1daylosws hdsl2shdslperfcurrdaycount、HDSL2 、HDSL2SHDSLENDPOINTCURRTIPRINGREVERVERSAL INTEGER、HDSL2SHDSLENDPOINTCURRACTIVESTATESTATE INTEGER}
hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current SNR margin for this endpoint as reported in a
Status Response/SNR message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
powerBackoff(1),
deviceFault(2),
dcContinuityFault(3),
snrMarginAlarm(4),
loopAttenuationAlarm(5),
loswFailureAlarm(6),
configInitFailure(7),
protocolInitFailure(8),
noNeighborPresent(9),
loopbackActive(10)
}
MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the current state of the endpoint. This is a bit-map of possible conditions. The various bit positions are as follows:
max-access読み取り専用ステータス現在の説明 "エンドポイントの現在の状態が含まれています。これは可能な条件のビットマップです。さまざまなビット位置は次のとおりです。
noDefect There are no defects on the line.
nodefect行に欠陥はありません。
powerBackoff Indicates enhanced Power Backoff.
Powerbackoffは、強化されたパワーバックオフを示します。
deviceFault Indicates that a vendor-dependent diagnostic or self-test fault has been detected.
DeviceFaultは、ベンダーに依存する診断またはセルフテスト障害が検出されたことを示しています。
dcContinuityFault Indicates vendor-dependent conditions that interfere with span powering such as short and open circuits.
dccontinuityFaultは、短い回路やオープンサーキットなどのスパンパワーを妨げるベンダー依存の条件を示します。
snrMarginAlarm Indicates that the SNR margin has dropped below the alarm threshold.
Snrmarginalarmは、SNRマージンがアラームしきい値を下回っていることを示しています。
loopAttenuationAlarm Indicates that the loop attenuation exceeds the alarm threshold.
LoopattenuationalArmは、ループ減衰がアラームしきい値を超えることを示します。
loswFailureAlarm Indicates a forward LOSW alarm.
loswfailurealarmは、前方のloswアラームを示しています。
configInitFailure Endpoint failure during initialization due to paired endpoint not able to support requested configuration.
configinitfailureエンドポイントの故障は、リクエストされた構成をサポートできないペアのエンドポイントによる初期化中。
protocolInitFailure Endpoint failure during initialization due to incompatible protocol used by the paired endpoint.
ペアのエンドポイントで使用される互換性のないプロトコルによる初期化中のプロトコリニットフェイルエンドポイント障害。
noNeighborPresent Endpoint failure during initialization due to no activation sequence detected from paired endpoint.
ペアのエンドポイントから検出された活性化シーケンスが検出されないため、初期化中のエンドポイントの障害はありません。
loopbackActive A loopback is currently active at this segment endpoint.
Loopbackactiveこのセグメントエンドポイントでは、ループバックが現在アクティブです。
This is intended to supplement ifOperStatus. Note that there is a 1:1 relationship between the status bits defined in this object and the notification thresholds defined elsewhere in this MIB module." REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
これは、Ifoperstatusを補足することを目的としています。このオブジェクトで定義されているステータスビットと、このMIBモジュールの他の場所で定義されている通知しきい値には1：1の関係があることに注意してください。 "参照" HDSL2セクション7.5.3.7。SHDSLセクション9.5.5.7 "
::= { hdsl2ShdslEndpointCurrEntry 3 }
hdsl2ShdslEndpointES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 4 }
hdsl2ShdslEndpointSES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 5 }
hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
SYNTAX Counter32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies on this endpoint since the xU was
last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 6 }
hdsl2ShdslEndpointLOSWS OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 7 }
hdsl2ShdslEndpointUAS OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 8 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 10 }
hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 11 }
hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE SYNTAX PerfCurrentCount UNITS "detected CRC Anomalies" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of CRC anomalies in the current 15-minute interval." REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
HDSL2SHDSLENDPOINTCURR15MINCRCANOMALIESオブジェクトタイプの構文PERFCURRENTCAUNTユニット "検出されたCRC異常「MAX-ACCESS読み取り専用ステータス現在の説明」「現在の15分間のCRC異常のカウント」。参照「HDSL2セクション7.5.3.7; SHDSLセクション9.5.5.7」
::= { hdsl2ShdslEndpointCurrEntry 12 }
hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 13 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the beginning of
the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 15 }
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 16 }
hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 17 }
hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 20 }
hdsl2ShdslEndpointCurrTipRingReversal OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
reversed(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the state of the tip/ring for the
wire pair."
::= { hdsl2ShdslEndpointCurrEntry 21 }
hdsl2ShdslEndpointCurrActivationState OBJECT-TYPE
SYNTAX INTEGER
{
preActivation(1), -- PreTrain
activation(2), -- Training
data(3) -- Trained
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the activation or training state of
the wire pair."
REFERENCE "ITU-T G.991.2, Section 6.2 PMD Activation Sequence"
::= { hdsl2ShdslEndpointCurrEntry 22 }
-- Segment Endpoint 15-Minute Interval Status/Performance Group --
- セグメントエンドポイント15分間隔ステータス/パフォーマンスグループ -
hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 6 }
hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2Shdsl15MinIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}
::= { hdsl2Shdsl15MinIntervalTable 1 }
Hdsl2Shdsl15MinIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl15MinIntervalNumber Unsigned32,
hdsl2Shdsl15MinIntervalES PerfIntervalCount,
hdsl2Shdsl15MinIntervalSES PerfIntervalCount,
hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount,
hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount,
hdsl2Shdsl15MinIntervalUAS PerfIntervalCount
}
hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval number. Interval 1 is the most
recent previous interval; interval 96 is 24 hours ago.
Intervals 2..96 are optional."
::= { hdsl2Shdsl15MinIntervalEntry 1 }
hdsl2Shdsl15MinIntervalES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 2 }
hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 3 }
hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 4 }
hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE
HDSL2SHDSL15MININTERVALLOSWSオブジェクトタイプ
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 5 }
hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 6 }
-- Segment Endpoint 1-Day Interval Status/Performance Group --
- セグメントエンドポイント1日間隔ステータス/パフォーマンスグループ -
hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 7 }
hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2Shdsl1DayIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }
::= { hdsl2Shdsl1DayIntervalTable 1 }
Hdsl2Shdsl1DayIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl1DayIntervalNumber Unsigned32,
hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed,
hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount
}
hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"History Data Interval number. Interval 1 is the most
recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional."
::= { hdsl2Shdsl1DayIntervalEntry 1 }
hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."
::= { hdsl2Shdsl1DayIntervalEntry 2 }
hdsl2Shdsl1DayIntervalES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 3 }
hdsl2Shdsl1DayIntervalSES OBJECT-TYPE SYNTAX Hdsl2Shdsl1DayIntervalCount UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Severely Errored Seconds (SES) during the 1-day
HDSL2SHDSL1DAYINTERVALSESオブジェクトタイプ構文HDSL2SHDSL1DAYINTERVALCOUNTユニット「秒」最大アクセスの読み取り専用ステータス現在の説明 "1日間の厳しいエラー秒（SES）のカウント（SES）カウント
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 4 }
hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 5 }
hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 6 }
hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day interval
as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 7 }
-- Maintenance Group --
- メンテナンスグループ -
hdsl2ShdslEndpointMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations (e.g., loopbacks)
to be performed on HDSL2/SHDSL segment endpoints. This table
contains live data from equipment. As such, it is NOT
persistent."
::= { hdsl2ShdslMibObjects 8 }
hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit, and the side of the unit."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }
::= { hdsl2ShdslEndpointMaintTable 1 }
Hdsl2ShdslEndpointMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackConfig INTEGER,
hdsl2ShdslMaintTipRingReversal INTEGER,
hdsl2ShdslMaintPowerBackOff INTEGER,
hdsl2ShdslMaintSoftRestart INTEGER
}
hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
SYNTAX INTEGER
{
noLoopback(1),
normalLoopback(2),
specialLoopback(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls configuration of loopbacks for the
associated segment endpoint. The status of the loopback
is obtained via the hdsl2ShdslEndpointCurrStatus object."
::= { hdsl2ShdslEndpointMaintEntry 1 }
hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
reversed(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the state of the tip/ring pair at the
associated segment endpoint."
::= { hdsl2ShdslEndpointMaintEntry 2 }
hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
SYNTAX INTEGER
{
default(1),
enhanced(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the receiver at the associated
segment endpoint to operate in default or enhanced power
backoff mode."
::= { hdsl2ShdslEndpointMaintEntry 3 }
hdsl2ShdslMaintSoftRestart OBJECT-TYPE
SYNTAX INTEGER
{
ready(1),
restart(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables the manager to trigger a soft restart
of the modem at the associated segment endpoint. The
manager may only set this object to the 'restart(2)'
value, which initiates a restart. The agent will perform a
restart after approximately 5 seconds. Following the 5 second
period, the agent will restore the object to the 'ready(1)'
state."
::= { hdsl2ShdslEndpointMaintEntry 4 }
hdsl2ShdslUnitMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations for units in a
HDSL2/SHDSL line. Entries in this table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 9 }
hdsl2ShdslUnitMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslUnitMaintTable. Each entry
corresponds to a single unit and is indexed by the
ifIndex of the HDSL2/SHDSL line and the UnitId of the
associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslUnitMaintTable 1 }
Hdsl2ShdslUnitMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER
}
hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
SYNTAX Integer32(0..4095)
UNITS "minutes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the timeout value for loopbacks
initiated at segments endpoints contained in the associated
unit. A value of 0 disables the timeout."
::= { hdsl2ShdslUnitMaintEntry 1 }
hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
SYNTAX INTEGER
{
local(1),
span(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the DC power source being used by the
associated unit."
::= { hdsl2ShdslUnitMaintEntry 2 }
-- Span Configuration Profile Group --
- スパン構成プロファイルグループ -
hdsl2ShdslSpanConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 10 }
hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. If an active
entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 }
Hdsl2ShdslSpanConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanConfWireInterface INTEGER,
hdsl2ShdslSpanConfMinLineRate Unsigned32,
hdsl2ShdslSpanConfMaxLineRate Unsigned32,
hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanConfRemoteEnabled INTEGER,
hdsl2ShdslSpanConfPowerFeeding INTEGER,
hdsl2ShdslSpanConfCurrCondTargetMarginDown Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32,
hdsl2ShdslSpanConfCurrCondTargetMarginUp Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp Integer32,
hdsl2ShdslSpanConfUsedTargetMargins BITS,
hdsl2ShdslSpanConfReferenceClock
Hdsl2ShdslClockReferenceType,
hdsl2ShdslSpanConfLineProbeEnable INTEGER,
hdsl2ShdslSpanConfProfileRowStatus RowStatus
}
hdsl2ShdslSpanConfProfileName OBJECT-TYPE
HDSL2SHDSLSPANCONFPROFILENAMEオブジェクトタイプ
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
::= { hdsl2ShdslSpanConfProfileEntry 1 }
hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
SYNTAX INTEGER
{
twoWire(1),
fourWire(2),
sixWire(3),
eightWire(4)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the two-wire or optional four-wire,
six-wire, or eight-wire operation for SHDSL lines."
DEFVAL { twoWire }
::= { hdsl2ShdslSpanConfProfileEntry 2 }
hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4294967295)
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps) and includes
both payload (user data) and any applicable framing overhead.
If the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the
maximum line rate, the line rate is considered
'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 3 }
hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE SYNTAX Unsigned32(0..4294967295) UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION
HDSL2SHDSLSPANCONFMAXLINETAL OBJECT-TYPE SYNTAX UNSIGN32（0..4294967295）ユニット "BPS" max-access read-createステータス現在の説明
"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps) and includes
both payload (user data) and any applicable framing overhead.
If the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the
maximum line rate, the line rate is considered
'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 4 }
hdsl2ShdslSpanConfPSD OBJECT-TYPE
SYNTAX INTEGER
{
symmetric(1),
asymmetric(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line. Support
for symmetric PSD is mandatory for all supported data rates.
Support for asymmetric PSD is optional."
DEFVAL { symmetric }
::= { hdsl2ShdslSpanConfProfileEntry 5 }
hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the regional setting for the SHDSL
line."
DEFVAL { { region1 } }
::= { hdsl2ShdslSpanConfProfileEntry 6 }
hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
SYNTAX INTEGER
{
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for remote management
of the units in an SHDSL line from the STU-R via the EOC."
DEFVAL { enabled }
::= { hdsl2ShdslSpanConfProfileEntry 7 }
hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
SYNTAX INTEGER
{
noPower(1),
powerFeed(2),
wettingCurrent(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for optional power
feeding in an SHDSL line."
DEFVAL { noPower }
::= { hdsl2ShdslSpanConfProfileEntry 8 }
hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream current condition target
SNR margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 9 }
hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream worst-case target SNR
margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 10 }
hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream current-condition target
SNR margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 11 }
hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream worst-case target SNR
margin for an SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 12 }
hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
SYNTAX BITS
{
currCondDown(0),
worstCaseDown(1),
currCondUp(2),
worstCaseUp(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Indicates whether a target SNR margin is enabled or
disabled. This is a bit-map of possible settings. The
various bit positions are as follows:
currCondDown - current-condition downstream target SNR margin enabled
Currconddown -Current ConditionのダウンストリームターゲットSNRマージンが有効になっています
worstCaseDown - worst-case downstream target SNR margin enabled
最悪の範囲 - 最悪のダウンストリームターゲットSNRマージンが有効になっています
currCondUp - current-condition upstream target SNR margin enabled
Currcondup-電流条件上流のターゲットSNRマージンが有効になっています
worstCaseUp - worst-case upstream target SNR margin enabled."
最悪のケースアップ - 最悪のケース上流のターゲットSNRマージンが有効になっています。」
DEFVAL { { currCondDown } }
::= { hdsl2ShdslSpanConfProfileEntry 13 }
hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE
SYNTAX Hdsl2ShdslClockReferenceType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the clock reference for the STU-C
in an SHDSL Line."
DEFVAL { localClk }
::= { hdsl2ShdslSpanConfProfileEntry 14 }
hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE
SYNTAX INTEGER
{
disable(1),
enable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for Line Probe of
the units in an SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate. If Line Probe is disabled, the rate adaptation phase
is skipped to shorten set up time."
DEFVAL { disable }
::= { hdsl2ShdslSpanConfProfileEntry 15 }
hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table per the semantics of RowStatus. If an
active entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
::= { hdsl2ShdslSpanConfProfileEntry 16 }
-- Segment Endpoint Alarm Configuration Profile group --
- セグメントエンドポイントアラーム構成プロファイルグループ -
hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of alarm configuration
profiles for HDSL2/SHDSL segment endpoints. This table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 11 }
hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single alarm configuration profile.
Each profile contains a set of parameters for setting alarm
thresholds for various performance attributes monitored at
HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
using the row creation/deletion mechanism via
hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active
entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
hdsl2ShdslEndpointThreshSNRMargin Integer32,
hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshSES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
}
hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the loop attenuation alarm threshold.
When the current value of hdsl2ShdslEndpointCurrAtn reaches
or exceeds this threshold, an hdsl2ShdslLoopAttenCrossing
MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the SNR margin alarm threshold.
When the current value of hdsl2ShdslEndpointCurrSnrMgn
reaches or drops below this threshold, a
hdsl2ShdslSNRMarginCrossing MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
hdsl2ShdslEndpointThreshES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Errored Seconds (ES) within any given 15-minute performance
data collection interval. If the value of Errored Seconds
in a particular 15-minute collection interval reaches/
exceeds this value, an hdsl2ShdslPerfESThresh MAY be
generated. At most, one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
hdsl2ShdslEndpointThreshSES OBJECT-TYPE SYNTAX Hdsl2ShdslPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION
hdsl2shdslendpointthreshses object-type構文HDSL2SHDSLPERFINTERVALTHRESHOLDユニット「秒」MAX-ACCESS READ-CREATEステータス現在の説明
"This object configures the threshold for the number of
Severely Errored Seconds (SES) within any given 15-minute
performance data collection interval. If the value of
Severely Errored Seconds in a particular 15-minute collection
interval reaches/exceeds this value, an hdsl2ShdslPerfSESThresh
MAY be generated. At most, one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
SYNTAX Integer32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
CRC anomalies within any given 15-minute performance data
collection interval. If the value of CRC anomalies in a
particular 15-minute collection interval reaches/exceeds
this value, an hdsl2ShdslPerfCRCanomaliesThresh MAY be
generated. At most, one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Loss of Sync Word (LOSW) Seconds within any given 15-minute
performance data collection interval. If the value of LOSW
in a particular 15-minute collection interval reaches/exceeds
this value, an hdsl2ShdslPerfLOSWSThresh MAY be generated.
At most, one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
hdsl2ShdslEndpointThreshUAS OBJECT-TYPE SYNTAX Hdsl2ShdslPerfIntervalThreshold UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION
hdsl2shdslendpointthreshuas object-type syntax hdsl2shdslperfintervalthresholdユニット「秒」max-access read-createステータス現在の説明
"This object configures the threshold for the number of
Unavailable Seconds (UAS) within any given 15-minute
performance data collection interval. If the value of UAS
in a particular 15-minute collection interval reaches/exceeds
this value, an hdsl2ShdslPerfUASThresh MAY be generated.
At most, one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus.
If an active entry is referenced in either
hdsl2ShdslSpanConfAlarmProfile or
hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
-- Notifications Group --
- 通知グループ -
hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }
hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAttenuation
}
STATUS current
DESCRIPTION
"This notification indicates that the loop attenuation
threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
value) has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."
::= { hdsl2ShdslNotifications 1 }
hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMargin
}
STATUS current
DESCRIPTION
"This notification indicates that the SNR margin threshold (as
per the hdsl2ShdslEndpointThreshSNRMargin value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 2 }
hdsl2ShdslPerfESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointThreshES
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds
threshold (as per the hdsl2ShdslEndpointThreshES value)
has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."
::= { hdsl2ShdslNotifications 3 }
hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointThreshSES
}
STATUS current
DESCRIPTION
"This notification indicates that the severely errored seconds
threshold (as per the hdsl2ShdslEndpointThreshSES value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 4 }
hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointThreshCRCanomalies
}
STATUS current
DESCRIPTION
"This notification indicates that the CRC anomalies threshold
(as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 5 }
hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPE
HDSL2SHDSLPERFLOSWSHRESH NOTIFITION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointThreshLOSWS
}
STATUS current
DESCRIPTION
"This notification indicates that the LOSW Seconds threshold
(as per the hdsl2ShdslEndpointThreshLOSWS value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 6 }
hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 7 }
hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslSpanConfNumRepeaters
}
STATUS current
DESCRIPTION
"This notification indicates that a mismatch has been detected
between the number of repeater/regenerator units configured
for an HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
object and the actual number of repeater/regenerator units
discovered via the EOC."
::= { hdsl2ShdslNotifications 8 }
hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslMaintLoopbackConfig
}
STATUS current
DESCRIPTION
"This notification indicates that an endpoint maintenance
loopback command failed for an HDSL2/SHDSL segment."
::= { hdsl2ShdslNotifications 9 }
hdsl2ShdslpowerBackoff NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 10 }
hdsl2ShdsldeviceFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
deviceFault in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 11 }
hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 12 }
hdsl2ShdslconfigInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
configInitFailure in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 13 }
hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
object for this endpoint has changed."
::= { hdsl2ShdslNotifications 14 }
hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 15 }
hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslInvVendorID
}
STATUS current
DESCRIPTION
"This notification indicates impending unit failure due to
loss of local power (last gasp)."
::= { hdsl2ShdslNotifications 16 }
-- conformance information --
- 適合情報 -
hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
hdsl2ShdslGroups OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 1 }
hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 2 }
-- agent compliance statements hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SNMP entities that implement HDSL2 and SHDSL. The version of SHDSL supported in this compliance statement is g.shdsl.
- エージェントコンプライアンスステートメントhdsl2Shdsllinemibcomplianceモジュールコンプライアンスステータス非推奨説明 "HDSL2およびSHDSLを実装するSNMPエンティティのコンプライアンスステートメント。このコンプライアンスステートメントでサポートされているSHDSLのバージョンはg.shdslです。
**** This compliance statement is deprecated. ****"
MODULE
MANDATORY-GROUPS
{
hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup
}
GROUP hdsl2ShdslInventoryShdslGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
グループHDSL2SHDSLINVENTORYSHDSLGROUP説明「このグループのサポートは、SHDSLラインをサポートする実装にのみ必要です。」
GROUP hdsl2ShdslSpanShdslStatusGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
グループHDSL2SHDSLSPANSHDSLSTATUSGROUP説明「このグループのサポートは、SHDSLラインをサポートする実装にのみ必要です。」
GROUP hdsl2ShdslSpanConfProfileGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
グループHDSL2SHDSLSPANCONFPROFILEGROUP説明「このグループのサポートは、SHDSLラインをサポートする実装にのみ必要です。」
OBJECT hdsl2ShdslSpanConfWireInterface
SYNTAX INTEGER
{
twoWire(1),
fourWire(2)
}
DESCRIPTION
"An implementation only has to support the range as
applicable for the original g.shdsl specification defined
in RFC 3276."
OBJECT hdsl2ShdslStatusMaxAttainableLineRate SYNTAX Unsigned32(0..4112000) DESCRIPTION "An implementation only has to support the range as applicable for the original g.shdsl specification defined in RFC 3276."
オブジェクトHDSL2SHDSLSTATUSMAXATAINABLELINETAL SYNTAX UNSTING32（0..4112000）説明
OBJECT hdsl2ShdslStatusActualLineRate SYNTAX Unsigned32(0..4112000) DESCRIPTION "An implementation only has to support the range as applicable for the original g.shdsl specification defined in RFC 3276."
オブジェクトHDSL2SHDSLSTATUSACTUALLINERET SYNTAX UNSTIGNED32（0..4112000）説明
OBJECT hdsl2ShdslSpanConfMinLineRate SYNTAX Unsigned32(0..4112000) DESCRIPTION "An implementation only has to support the range as applicable for the original g.shdsl specification defined in RFC 3276."
オブジェクトHDSL2SHDSLSPANCONFMINLINETAL SYNTAX UNSIGNED32（0..4112000）説明
OBJECT hdsl2ShdslSpanConfMaxLineRate SYNTAX Unsigned32(0..4112000) DESCRIPTION "An implementation only has to support the range as applicable for the original g.shdsl specification defined in RFC 3276."
オブジェクトHDSL2SHDSLSPANCONFMAXLINETAL SYNTAX UNSIGNED32（0..4112000）説明
::= { hdsl2ShdslCompliances 1 }
hdsl2GshdslbisLineMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities that implement
HDSL2 and SHDSL. The version of SHDSL supported in this
compliance statement is g.shdsl.bis."
MODULE
MANDATORY-GROUPS
{
hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup
}
GROUP hdsl2ShdslInventoryShdslGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
グループHDSL2SHDSLINVENTORYSHDSLGROUP説明「このグループのサポートは、SHDSLラインをサポートする実装にのみ必要です。」
GROUP hdsl2ShdslSpanShdslStatusGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
グループHDSL2SHDSLSPANSHDSLSTATUSGROUP説明「このグループのサポートは、SHDSLラインをサポートする実装にのみ必要です。」
GROUP hdsl2ShdslSpanConfProfileGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
グループHDSL2SHDSLSPANCONFPROFILEGROUP説明「このグループのサポートは、SHDSLラインをサポートする実装にのみ必要です。」
GROUP hdsl2ShdslWirePairGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
グループHDSL2SHDSLWIREPAIRGROUP説明「このグループのサポートは、SHDSLラインをサポートする実装にのみ必要です。」
GROUP hdsl2ShdslPayloadRateGroup DESCRIPTION "Support for this group is only required for implementations supporting SHDSL lines."
グループHDSL2SHDSLPAYLOADRATEGROUP説明「このグループのサポートは、SHDSLラインをサポートする実装にのみ必要です。」
::= { hdsl2ShdslCompliances 2 }
-- units of conformance --
- 適合ユニット -
hdsl2ShdslSpanConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslSpanConfNumRepeaters,
hdsl2ShdslSpanConfProfile,
hdsl2ShdslSpanConfAlarmProfile
}
STATUS current
DESCRIPTION
"This group supports objects for configuring span-related
parameters for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 1 }
hdsl2ShdslSpanStatusGroup OBJECT-GROUP OBJECTS
HDSL2SHDSLSPANSTATATUSGROUPオブジェクトグループオブジェクト
{
hdsl2ShdslStatusNumAvailRepeaters
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving span-related
status for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 2 }
hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvTransmissionModeCapability
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
inventory information."
::= { hdsl2ShdslGroups 3 }
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
span-related status."
::= { hdsl2ShdslGroups 4 }
hdsl2ShdslInventoryGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvVendorID,
hdsl2ShdslInvVendorModelNumber,
hdsl2ShdslInvVendorSerialNumber,
hdsl2ShdslInvVendorEOCSoftwareVersion,
hdsl2ShdslInvStandardVersion,
hdsl2ShdslInvVendorListNumber,
hdsl2ShdslInvVendorIssueNumber,
hdsl2ShdslInvVendorSoftwareVersion,
hdsl2ShdslInvEquipmentCode,
hdsl2ShdslInvVendorOther
}
STATUS current
DESCRIPTION
"This group supports objects that provide unit inventory
information about the units in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 5 }
hdsl2ShdslEndpointConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn
}
STATUS current
DESCRIPTION
"This group supports objects for configuring parameters for
segment endpoints in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 6 }
hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointCurrStatus,
hdsl2ShdslEndpointES,
hdsl2ShdslEndpointSES,
hdsl2ShdslEndpointCRCanomalies,
hdsl2ShdslEndpointLOSWS,
hdsl2ShdslEndpointUAS,
hdsl2ShdslEndpointCurr15MinTimeElapsed,
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointCurr1DayTimeElapsed,
hdsl2ShdslEndpointCurr1DayES,
hdsl2ShdslEndpointCurr1DaySES,
hdsl2ShdslEndpointCurr1DayCRCanomalies,
hdsl2ShdslEndpointCurr1DayLOSWS,
hdsl2ShdslEndpointCurr1DayUAS
}
STATUS current
DESCRIPTION
"This group supports objects that provide current status and
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 7 }
hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP
HDSL2SHDSL15MININTERVALGROUPオブジェクトグループ
OBJECTS
{
hdsl2Shdsl15MinIntervalES,
hdsl2Shdsl15MinIntervalSES,
hdsl2Shdsl15MinIntervalCRCanomalies,
hdsl2Shdsl15MinIntervalLOSWS,
hdsl2Shdsl15MinIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects that maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 15-minute intervals."
::= { hdsl2ShdslGroups 8 }
hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
OBJECTS
{
hdsl2Shdsl1DayIntervalMoniSecs,
hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects that maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 1-day intervals."
::= { hdsl2ShdslGroups 9 }
hdsl2ShdslMaintenanceGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslMaintLoopbackConfig,
hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff,
hdsl2ShdslMaintSoftRestart,
hdsl2ShdslMaintLoopbackTimeout,
hdsl2ShdslMaintUnitPowerSource
}
STATUS current
DESCRIPTION
"This group supports objects that provide support for
maintenance actions for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 10 }
hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointAlarmConfProfile,
hdsl2ShdslEndpointThreshLoopAttenuation,
hdsl2ShdslEndpointThreshSNRMargin,
hdsl2ShdslEndpointThreshES,
hdsl2ShdslEndpointThreshSES,
hdsl2ShdslEndpointThreshCRCanomalies,
hdsl2ShdslEndpointThreshLOSWS,
hdsl2ShdslEndpointThreshUAS,
hdsl2ShdslEndpointAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that allow configuration of alarm
thresholds for various performance parameters for HDSL2/SHDSL
lines."
::= { hdsl2ShdslGroups 11 }
hdsl2ShdslNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
hdsl2ShdslLoopAttenCrossing,
hdsl2ShdslSNRMarginCrossing,
hdsl2ShdslPerfESThresh,
hdsl2ShdslPerfSESThresh,
hdsl2ShdslPerfCRCanomaliesThresh,
hdsl2ShdslPerfLOSWSThresh,
hdsl2ShdslPerfUASThresh,
hdsl2ShdslSpanInvalidNumRepeaters,
hdsl2ShdslLoopbackFailure,
hdsl2ShdslpowerBackoff,
hdsl2ShdsldeviceFault,
hdsl2ShdsldcContinuityFault,
hdsl2ShdslconfigInitFailure,
hdsl2ShdslprotocolInitFailure,
hdsl2ShdslnoNeighborPresent,
hdsl2ShdslLocalPowerLoss
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 12 }
hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP OBJECTS
HDSL2SHDSLSPANCONFPROFILEGROUPオブジェクトグループオブジェクト
{
hdsl2ShdslSpanConfWireInterface,
hdsl2ShdslSpanConfMinLineRate,
hdsl2ShdslSpanConfMaxLineRate,
hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode,
hdsl2ShdslSpanConfRemoteEnabled,
hdsl2ShdslSpanConfPowerFeeding,
hdsl2ShdslSpanConfCurrCondTargetMarginDown,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
hdsl2ShdslSpanConfCurrCondTargetMarginUp,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
hdsl2ShdslSpanConfUsedTargetMargins,
hdsl2ShdslSpanConfReferenceClock,
hdsl2ShdslSpanConfLineProbeEnable,
hdsl2ShdslSpanConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that constitute configuration
profiles for configuring span-related parameters in SHDSL
lines."
::= { hdsl2ShdslGroups 13 }
hdsl2ShdslWirePairGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrTipRingReversal,
hdsl2ShdslEndpointCurrActivationState
}
STATUS current
DESCRIPTION
"This group supports objects that provide the status
of SHDSL-specific wire pairs."
::= { hdsl2ShdslGroups 14 }
hdsl2ShdslPayloadRateGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainablePayloadRate,
hdsl2ShdslStatusActualPayloadRate
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving payload rates
that exclude any framing overhead."
::= { hdsl2ShdslGroups 15 }
END
終わり
A management application that supports RFC 3276 could mistakenly flag a unit that responds with a rate or wire pair that exceeds the ranges and/or enumerations specified in RFC 3276. For example, a G.shdsl.bis line with four wire pairs would report statistics for wire pairs that do not exist in RFC 3276. That is, a GET-NEXT request issues with the object identifier:
RFC 3276をサポートする管理アプリケーションは、RFC 3276で指定された範囲および/または列挙を超えるレートまたはワイヤーペアで応答するユニットに誤ってフラグを立てることができます。たとえば、4つのワイヤペアを持つG.Shdsl.bisラインは統計を報告しますRFC 3276には存在しないワイヤペアの場合。つまり、オブジェクト識別子のGet-Nextリクエストの問題：
hdsl2ShdslEndpointCurrAtn.1.1.1.2
hdsl2shdslendpointcurratn.1.1.1.2
might return
戻るかもしれません
hdsl2ShdslEndpointCurrAtn.1.1.1.3 = 0
hdsl2shdslendpointcurratn.1.1.1.3 = 0
with a G.shdsl.bis unit and
g.shdsl.bisユニットと
hdsl2ShdslEndpointCurrSnrMgn.1.1.1.1 = 0
hdsl2shdslendpointcurrsnrmgn.1.1.1.1 = 0
with an HDSL2 unit as these objects are indexed by
これらのオブジェクトがでインデックス作成されるように、HDSL2ユニットを使用して
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslendpointSide, hdsl2ShdslEndpointWirePair }
index {ifindex、hdsl2shdslinvindex、hdsl2shdslendpointside、hdsl2shdslendpointwirepair}
A management application intended to manage G.shdsl.bis agents SHOULD be modified to accept this sequence.
g.shdsl.bisエージェントを管理することを目的とした管理アプリケーションは、このシーケンスを受け入れるように変更する必要があります。
One should note that this same unmodified management application is still capable of managing G.shdsl.bis agents albeit to the degree of G.SHDSL (non-bis) limitations. That is, it can create and monitor configurations limited to two wire pairs with an upper-rate limit of 4112000 bits/second.
この同じ変更されていない管理アプリケーションは、G.Shdsl（非BIS）の制限の程度にもかかわらず、g.shdsl.bisエージェントを管理できることに注意する必要があります。つまり、4112000ビット/秒の上限制限で、2つのワイヤペアに制限された構成を作成および監視できます。
There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: o hdsl2ShdslSpanConfTable
このMIBモジュールには、読み取りワイトおよび/またはread-Createの最大アクセス句を備えた管理オブジェクトが多数あります。このようなオブジェクトは、一部のネットワーク環境で敏感または脆弱と見なされる場合があります。適切な保護なしの非セキュア環境でのセット操作のサポートは、ネットワーク操作に悪影響を与える可能性があります。これらはテーブルとオブジェクトであり、その感度/脆弱性：o hdsl2shdslspanconftable
The table consists of the following objects that support SET operations:
テーブルは、操作のセットをサポートする次のオブジェクトで構成されています。
* hdsl2ShdslSpanConfNumRepeaters
* hdsl2ShdslSpanConfProfile
* hdsl2ShdslSpanConfAlarmProfile
* HDSL2SHDSLSPANCONFNUMREPEATERS
* hdsl2shdslspanconfprofile
* HDSL2SHDSLSPANCONFALARMPROFILE
Unauthorized changes to hdsl2ShdslSpanConfNumRepeaters could result in an hdsl2ShdslSpanInvalidNumRepeaters notification. Note the discussion on hdsl2ShdslSpanInvalidNumRepeaters in the Notifications section above.
HDSL2SHDSLSPANCONFNUMREPEATERSの不正な変更により、HDSL2SHDSLSPANINVALIDNUMREPEATERSの通知が発生する可能性があります。上記の通知セクションのHDSL2SHDSLSPANINVALIDNUMREPEATERSの議論に注意してください。
Unauthorized changes to hdsl2ShdslSpanConfProfile could have an adverse operational effect on a span. Reference the hdsl2ShdslSpanConfProfileTable discussion below.
HDSL2SHDSLSPANCONFPROFILEの不正な変更は、スパンに悪影響を与える可能性があります。以下のHDSL2SHDSLSPANCONFPROFILETABLE FILESTABLEの説明を参照してください。
Unauthorized changes to hdsl2ShdslSpanConfAlarmProfile could have a contrary effect on notifications. Reference the hdsl2ShdslEndpointAlarmConfProfileTable discussion below.
HDSL2SHDSLSPANCONFALARMPROFILEの不正な変更は、通知に反対の影響を与える可能性があります。以下のHDSL2SHDSLENDPOINTALARMCONFPROFILETABLE FILSECTABLEを参照してください。
o hdsl2ShdslEndpointConfTable
o HDSL2SHDSLENDPOINTCONFTABLE
This table contains one object, hdsl2ShdslEndpointAlarmConfProfile, that supports SET operations. Unauthorized changes could have an undesirable notifications. Reference the hdsl2ShdslEndpointAlarmConfProfileTable discussion below.
このテーブルには、設定された操作をサポートする1つのオブジェクト、HDSL2SHDSLENDPOINTALARMCONFPROFILEが含まれています。許可されていない変更には、望ましくない通知があります。以下のHDSL2SHDSLENDPOINTALARMCONFPROFILETABLE FILSECTABLEを参照してください。
o hdsl2ShdslEndpointMaintTable
o hdsl2shdslendpointmainttable
The table consists of the following objects that support SET operations:
テーブルは、操作のセットをサポートする次のオブジェクトで構成されています。
* hdsl2ShdslMaintLoopbackConfig
* hdsl2ShdslMaintPowerBackoff
* hdsl2ShdslMaintSoftRestart
* hdsl2shdslmaintloopbackconfig
* hdsl2shdslmaintpowerbackoff
* HDSL2SHDSLMAINTSOFTRESTART
Unauthorized changes to hdsl2ShdslMaintLoopbackConfig could prevent end-to-end data transfer due to an activation of a loopback.
hdsl2shdslmaintloopbackconfigの不正な変更は、ループバックの活性化によりエンドツーエンドのデータ転送を防ぐことができます。
Unauthorized changes to hdsl2ShdslMaintPowerBackoff could result in an increased in bundle interference.
hdsl2shdslmaintpowerbackoffの不正な変更により、バンドル干渉が増加する可能性があります。
Unauthorized changes to hdsl2ShdslMaintSoftRestart could result in a temporary interruption of end-to-end data transfer as the result of the triggering of a soft restart.
HDSL2SHDSLMAINTSOFTRESTARTの不正な変更により、ソフト再起動のトリガーの結果として、エンドツーエンドのデータ転送が一時的に中断される可能性があります。
o hdsl2ShdslUnitMaintTable
o hdsl2shdslunitmainttable
This table contains one object, hdsl2ShdslMaintLoopbackTimeout, that supports SET operations. An unauthorized change to this object could result in the timeout value for loopbacks being increased, decreased, or disabled.
このテーブルには、設定された操作をサポートする1つのオブジェクト、HDSL2SHDSLMANTLOOPBACKTIMEOUTが含まれています。このオブジェクトに対する不正な変更により、ループバックのタイムアウト値が増加、減少、または無効になる可能性があります。
o hdsl2ShdslSpanConfProfileTable
o HDSL2SHDSLSPANCONFPROFILETABLE
The table consists of the following objects that support SET operations:
テーブルは、操作のセットをサポートする次のオブジェクトで構成されています。
* hdsl2ShdslSpanConfWireInterface
* hdsl2ShdslSpanConfMinLineRate
* hdsl2ShdslSpanConfMaxLineRate
* hdsl2ShdslSpanConfPSD
* hdsl2ShdslSpanConfTransmissionMode
* hdsl2ShdslSpanConfRemoteEnabled
* hdsl2ShdslSpanConfPowerFeeding
* hdsl2ShdslSpanConfCurrCondTargetMarginDown
* hdsl2ShdslSpanConfWorstCaseTargetMarginDown
* hdsl2ShdslSpanConfCurrCondTargetMarginUp
* hdsl2ShdslSpanConfWorstCaseTargetMarginUp
* hdsl2ShdslSpanConfUsedTargetMargins
* hdsl2ShdslSpanConfReferenceClock
* hdsl2ShdslSpanConfLineProbeEnable
* hdsl2ShdslSpanConfProfileRowStatus
* HDSL2SHDSLSPANCONFWIREINTERFACE
* HDSL2SHDSLSPANCONFMINLINERET
* HDSL2SHDSLSPANCONFMAXLINETAL
* HDSL2SHDSLSPANCONFPSD
* HDSL2SHDSLSPANCONFTRANSMISSIONMODE
* HDSL2SHDSLSPANCONFREMOTEENABLED
* HDSL2SHDSLSPANCONFPOWEREDING
* HDSL2SHDSLSPANCONFCURRCONDTARGETMARGINDOWN
* HDSL2SHDSLSPANCONFWORSTCASETARGETMARGINDOWN
* HDSL2SHDSLSPANCONFCURRCONDTARGETMARGINUP
* hdsl2shdslspanconfworstcasetargetmarginup
* HDSL2SHDSLSPANCONFUSEDTARGETMARGINS
* HDSL2SHDSLSPANCONFREFERENCECLOCK
* HDSL2SHDSLSPANCONFLINEPROBEENABLE
* HDSL2SHDSLSPANCONFPROFILEROWSTATUS
Setting any of the objects to an incorrect value could have an adverse operational effect on a span.
オブジェクトのいずれかを誤った値に設定すると、スパンに悪影響を与える可能性があります。
Unauthorized changes to the hdsl2ShdslSpanConfWireInterface could result in the failure of a span to achieve activation to a state that would permit data flow. For example, setting this object to six-wire or eight-wire operation when one of the units in the span only supports two-wire or four-wire operation would likely prevent an expected end-to-end data transfer capability.
HDSL2SHDSLSPANCONFWIREINTERFACEへの不正な変更により、データフローを許可する状態へのアクティベーションを達成できなくなった可能性があります。たとえば、このオブジェクトを6線または8線操作に設定すると、SPANのユニットの1つが2線または4線操作のみをサポートすると、予想されるエンドツーエンドのデータ転送機能が妨げられる可能性があります。
Unauthorized changes to hdsl2ShdslSpanConfMinLineRate or hdsl2ShdslSpanConfMaxLineRate could have an adverse effect on performance. The range of allowable line rates could be altered such that the span may not be able to train to a line rate that would permit any end-user data to traverse the span or the span could train to a line rate that is either greater than or less than the line rate that the provider has pledged.
hdsl2shdslspanconfminlinerateまたはhdsl2shdslspanconfmaxlinerateの不正な変更は、パフォーマンスに悪影響を与える可能性があります。許容線速度の範囲は、スパンがエンドユーザーデータがスパンを横断することを可能にするラインレートまでトレーニングできないように、またはスパンがより大きいラインレートまでトレーニングできないように変更できます。プロバイダーが誓約したライン率よりも少ない。
Unauthorized changes to hdsl2ShdslSpanConfPSD or hdsl2ShdslSpanConfTransmissionMode could have a detrimental effect on loop reach, performance, or spectral compatibility.
HDSL2SHDSLSPANCONFPSDまたはHDSL2SSLSPANCONFTRANSMISIONMODEの不正な変更は、ループリーチ、パフォーマンス、またはスペクトル互換性に有害な影響を与える可能性があります。
Unauthorized changes to hdsl2ShdslSpanConfRemoteEnable could alter the remote management ability of units.
hdsl2shdslspanconfremoteenableの不正な変更は、ユニットのリモート管理能力を変える可能性があります。
Unauthorized changes to hdsl2ShdslSpanConfPowerFeeding could shutdown units that are expected to be fed power remotely. Changing the configuration such that wetting current is not supplied may result in corrosion of electrical contacts.
HDSL2SHDSLSPANCONFPOWERFEEDINGの不正な変更は、電力をリモートで供給されると予想されるユニットをシャットダウンする可能性があります。湿潤電流が供給されないように構成を変更すると、電気接点が腐食する可能性があります。
Unauthorized changes to hdsl2ShdslSpanConfCurrCondTargetMarginDown, hdsl2ShdslSpanConfWorstCaseTargetMarginDown, hdsl2ShdslSpanConfCurrCondTargetMarginUp, hdsl2ShdslSpanConfWorstCaseTargetMarginUp, or hdsl2ShdslSpanConfUsedTargetMargins could result in invalid parameters used to determine if a data rate can be supported under current and worst-case noise.
hdsl2Shdslspanconfcurrcondtargetmargindown、hdsl2sslslspanconfworstcasetargetmargindown、hdsl2shdslspanconfcurrcondtargetmarginup、hdsl2shdslspanconfworstcasegtrgetmarggetmarggetmgrggetmarggetmatrggetmarggetmarggetmarggetrggetmarginupのhdsl2sslspanconfworstcasetargetmargindown、hdsl2shdslspanconfworstcasetargetmargindownの不正な変更を許可しない変更マージンは、現在および最悪のノイズの下でデータレートをサポートできるかどうかを判断するために使用される無効なパラメーターをもたらす可能性があります。
Unauthorized changes to hdsl2ShdslSpanConfReferenceClock could result in the selection of a clock source that might either prevent any data from being transferred or impair data transfer. In addition, an increase in CRC anomalies may be experienced.
HDSL2SHDSLSPANCONFREFERENCECLOCKの不正な変更により、データの転送を防ぐか、データ転送を損なう可能性のあるクロックソースが選択される可能性があります。さらに、CRC異常の増加が経験される場合があります。
Unauthorized changes to hdsl2ShdslSpanConfLineProbeEnable could have a negative effect on selecting the optimum rate or power level based on current line conditions.
HDSL2SHDSLSPANCONFLINEPROBEENABLEの不正な変更は、現在のライン条件に基づいて最適なレートまたはパワーレベルの選択にマイナスの影響を与える可能性があります。
Unauthorized changes to row status could result in unwanted profiles being created or brought into service. Also, changes to the row status could result in profiles being inadvertently deleted or taken out of service.
行のステータスに対する不正な変更により、不要なプロファイルが作成または使用される可能性があります。また、行のステータスを変更すると、プロファイルが不注意に削除されたり、使用しなくなったりする可能性があります。
o hdsl2ShdslEndpointAlarmConfProfileTable
o HDSL2SHDSLENDPOINTALARMCONFPROFILETABLE
The table consists of the following objects that support SET operations:
テーブルは、操作のセットをサポートする次のオブジェクトで構成されています。
* hdsl2ShdslEndpointThreshLoopAttenuation
* hdsl2ShdslEndpointThreshSNRMargin
* hdsl2ShdslEndpointThreshES
* hdsl2ShdslEndpointThreshSES
* hdsl2shdslendpointthreshloopattenuation
* HDSL2SHDSLENDPOINTTHRESHSNRMARGIN
* HDSL2SHDSLENDPOINTHRESHES
* HDSL2SHDSLENDPOINTTHRESHSES
* hdsl2ShdslEndpointThreshCRCanomalies
* hdsl2ShdslEndpointThreshLOSWS
* hdsl2ShdslEndpointThreshUAS
* hdsl2ShdslEndpointAlarmConfProfileRowStatus
* HDSL2SHDSLENDPOINTTHRESHCRCANOMALIES
* HDSL2SHDSLENDPOINTTHRESHLOSWS
* HDSL2SHDSLENDPOINTTHRESHUAS
* HDSL2SHDSLENDPOINTALARMCONFPROFILEROWSTATUS
Increasing any of the threshold values could result in a notification being suppressed or deferred. Setting a threshold to 0 could result in a notification being suppressed. Suppressing or deferring a notification could prevent the timely delivery of important diagnostic information. Decreasing any of the threshold values could result in a notification being sent from the network falsely reporting a threshold crossing.
しきい値のいずれかを増やすと、通知が抑制または延期される可能性があります。しきい値を0に設定すると、通知が抑制される可能性があります。通知を抑制または延期すると、重要な診断情報のタイムリーな配信が妨げられる可能性があります。しきい値のいずれかを減らすと、ネットワークから通知が送信され、しきい値の交差を誤って報告する可能性があります。
Changing a threshold value could also have an impact on the amount of notifications the agent sends. This document adds a paragraph, which was not in RFC 3276 [RFC3276], to the Notifications section that provides general guidance to the rate limiting of notifications. Agent implementations not adhering to the rate-limiting desires could result in notifications being generated at an uncontrolled rate. Unauthorized changes to a threshold value could result in an undesired notification rate.
しきい値を変更すると、エージェントが送信する通知の量にも影響を与える可能性があります。このドキュメントは、通知のレート制限に対する一般的なガイダンスを提供する通知セクションに、RFC 3276 [RFC3276]にない段落を追加します。レート制限の欲求を順守していないエージェントの実装により、通知が制御されていないレートで生成される可能性があります。しきい値に対する不正な変更により、望ましくない通知率が得られる可能性があります。
Unauthorized changes to row status could result in unwanted profiles being created or brought into service. Also, changes to the row status could result in profiles being inadvertently deleted or taken out of service.
行のステータスに対する不正な変更により、不要なプロファイルが作成または使用される可能性があります。また、行のステータスを変更すると、プロファイルが不注意に削除されたり、使用しなくなったりする可能性があります。
Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability:
このMIBモジュールの読み取り可能なオブジェクトのいくつか（つまり、アクセスできないこと以外に最大アクセスを備えたオブジェクト）は、一部のネットワーク環境で敏感または脆弱と見なされる場合があります。したがって、これらのオブジェクトへのアクセスを取得および/または通知することさえ制御し、SNMPを介してネットワーク上に送信するときにこれらのオブジェクトの値を暗号化することも重要です。これらはテーブルとオブジェクトであり、その感度/脆弱性です。
o hdsl2ShdslInventoryTable
o HDSL2SHDSLINVENTORYTABLE
Access to these objects would allow an intruder to obtain information about which vendor's equipment is in use on the network. Further, such information is considered sensitive in many environments for competitive reasons.
これらのオブジェクトへのアクセスにより、侵入者はネットワークで使用されているベンダーの機器に関する情報を取得できます。さらに、そのような情報は、競争上の理由で多くの環境で敏感であると考えられています。
* hdsl2ShdslInvVendorID
* hdsl2ShdslInvVendorModelNumber
* hdsl2ShdslInvVendorSerialNumber
* hdsl2ShdslInvVendorEOCSoftwareVersion
* hdsl2ShdslInvStandardVersion
* hdsl2ShdslInvVendorListNumber
* HDSL2SHDSLINVVENDORID
* HDSL2SHDSLINVVENDOMODELNUMBER
* HDSL2SHDSLINVVENDORSERIALNUMBER
* HDSL2SHDSLINVVENDOREOCSOFTWAREVERSION
* HDSL2SHDSLINVSTANDARDVERSION
* HDSL2SHDSLINVVENDORLISTNUMBER
* hdsl2ShdslInvVendorIssueNumber
* hdsl2ShdslInvVendorSoftwareVersion
* hdsl2ShdslInvEquipmentCode
* hdsl2ShdslInvVendorOther
* hdsl2ShdslInvTransmissionModeCapability
* HDSL2SHDSLINVVENDORISSUENUMBER
* HDSL2SHDSLINVVENDORSOFTWAREVERSION
* hdsl2shdslinvequipmentcode
* HDSL2SHDSLINVVENDOROTHER
* HDSL2SHDSLINVTRANSMISSIONMODECAPABILITY
SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module.
SNMPV3以前のSNMPバージョンには、適切なセキュリティは含まれていませんでした。ネットワーク自体が（たとえばIPSECを使用して）安全である場合でも、それでもセキュアネットワーク上の誰がアクセス/セット/セット（読み取り/変更/作成/削除/削除）を制御することはできません。MIBモジュール。
It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], Section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy).
実装者は、SNMPV3暗号化メカニズム（認証とプライバシー用）の完全なサポートを含む、SNMPV3フレームワーク（[RFC3410]、セクション8を参照）で提供されるセキュリティ機能を考慮することをお勧めします。
Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them.
さらに、SNMPV3より前のSNMPバージョンの展開は推奨されません。代わりに、SNMPV3を展開し、暗号化セキュリティを有効にすることをお勧めします。その場合、このMIBモジュールのインスタンスへのアクセスを提供するSNMPエンティティが、実際に取得または設定する正当な権利を持つプリンシパル（ユーザー）にのみオブジェクトにアクセスできるように適切に構成されていることを保証するのは、顧客/オペレーターの責任です（変更を変更します（変更）/作成/削除）それら。
The authors are deeply grateful to the authors of the ADSL LINE MIB (RFC 2662 [RFC2662]), Gregory Bathrick and Faye Ly, as much of the text and structure of this document originate in their documents.
著者は、ADSL Line MIB（RFC 2662 [RFC2662]）、Gregory Bathrick、Faye Lyの著者に深く感謝しています。
The authors are also grateful to the authors of FR MFR MIB (RFC 3020 [RFC3020]), Prayson Pate, Bob Lynch, and Kenneth Rehbehn, as the majority of the Security Considerations section was lifted from their document.
著者は、セキュリティに関する考慮事項の大部分が文書から解除されたため、Fr Mfr Mib（RFC 3020 [RFC3020]）、Prayson Pate、Bob Lynch、およびKenneth Rehbehnの著者にも感謝しています。
The authors also acknowledge the importance of the contributions and suggestions regarding interface indexing structures received from David Horton of CITR.
著者はまた、CITRのDavid Hortonから受け取ったインターフェイスインデックス作成構造に関する貢献と提案の重要性を認めています。
The authors are extremely thankful to Bert Wijnen, Randy Presuhn, and C. M. Heard for their extensive review and the many suggestions they provided.
著者は、Bert Wijnen、Randy Presuhn、およびC. M.に非常に感謝しています。
Other contributions were received from the following:
その他の貢献は以下から受け取りました。
Matt Beanland (Extel Communications) Philip Bergstresser (Adtran) Steve Blackwell (Centillium) Umberto Bonollo (NEC Australia) John Egan (Metalink BroadBand) Yagal Hachmon (RAD) Mark Johnson (Red Point) Sharon Mantin (Orckit) Moti Morgenstern (ECI) Raymond Murphy (Ericsson) Lee Nipper (Verilink) Randy Presuhn (BMC Software) Katy Sherman (Orckit) Mike Sneed (ECI) Jon Turney (DSL Solutions) Aron Wahl (Memotec) Bert Wijnen (Lucent) Jim Wilson (for Mindspeed) Michael Wrobel (Memotec)
マットビーンランド（エクステルコミュニケーションズ）フィリップバーグストレッサー（アドトラン）スティーブブラックウェル（センチリウム）ウンベルトボノロ（NECオーストラリア）ジョンイーガン（メタンクブロードバンド）ヤガルハッハモン（ラッド）マークジョンソン（レッドポイント）シャロンマンティン（オルキット）モティモーゲンスター（ECI）レイモンドマーフィー（エリクソン）リー・ニッパー（Verilink）Randy Presuhn（BMC Software）Katy Sherman（Orckit）Mike Sneed（ECI）Jon Turney（DSL Solutions）Aron Wahl（Memotec）Bert Wijnen（Lucent）Jim Wilson（MindSepeed）Michael Wobel（memotec）
[G.991.2] Blackwell, S., "Single-Pair High-Speed Digital Subscriber Line (SHDSL) Transceivers", ITU-T G.991.2, December 2003.
[G.991.2] Blackwell、S。、「シングルペア高速デジタルサブスクライバーライン（SHDSL）トランシーバー」、ITU-T G.991.2、2003年12月。
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2119] Bradner、S。、「要件レベルを示すためにRFCで使用するためのキーワード」、BCP 14、RFC 2119、1997年3月。
[RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[RFC2578] McCloghrie、K.、Perkins、D。、およびJ. Schoenwaelder、「管理情報の構造バージョン2（SMIV2）」、STD 58、RFC 2578、1999年4月。
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[RFC2579] McCloghrie、K.、Perkins、D。、およびJ. Schoenwaelder、「SMIV2のテキストコンベンション」、STD 58、RFC 2579、1999年4月。
[RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999.
[RFC2580] McCloghrie、K.、Perkins、D。、およびJ. Schoenwaelder、「SMIV2の適合ステートメント」、STD 58、RFC 2580、1999年4月。
[RFC2863] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000.
[RFC2863] McCloghrie、K。およびF. Kastenholz、「The Interfaces Group MIB」、RFC 2863、2000年6月。
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", STD 62, RFC 3411, December 2002.
[RFC3411] Harrington、D.、Presuhn、R。、およびB. Wijnen、「単純なネットワーク管理プロトコル（SNMP）管理フレームワークを説明するためのアーキテクチャ」、STD 62、RFC 3411、2002年12月。
[RFC3593] Tesink, K., "Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals", RFC 3593, September 2003.
[RFC3593] Tesink、K。、「15分間隔に基づくパフォーマンス履歴を使用したMIBモジュールのテキストコンベンション」、RFC 3593、2003年9月。
[T1E1.4] American National Standards Institute, "ANSI T1E1.4/2000- 006", February 2000.
[T1E1.4] American National Standards Institute、「ANSI T1E1.4/2000- 006」、2000年2月。
[RFC2662] Bathrick, G. and F. Ly, "Definitions of Managed Objects for the ADSL Lines", RFC 2662, August 1999.
[RFC2662] Bathrick、G。およびF. Ly、「ADSLラインの管理オブジェクトの定義」、RFC 2662、1999年8月。
[RFC3020] Pate, P., Lynch, B., and K. Rehbehn, "Definitions of Managed Objects for Monitoring and Controlling the UNI/NNI Multilink Frame Relay Function", RFC 3020, December 2000.
[RFC3020] Pate、P.、Lynch、B。、およびK. Rehbehn、「Uni/NNI Multilink Frame Relay Functionを監視および制御するための管理オブジェクトの定義」、RFC 3020、2000年12月。
[RFC3276] Ray, B. and R. Abbi, "Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair High-Speed Digital Subscriber Line (SHDSL) Lines Processing", RFC 3276, May 2002.
[RFC3276] Ray、B。およびR. Abbi、「高額のDSL-2nd Generation（HDSL2）およびシングルペア高速デジタルサブスクライバーライン（SHDSL）ライン処理のための管理されたオブジェクトの定義」、RFC 3276、May May2002年。
[RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002.
[RFC3410] Case、J.、Mundy、R.、Partain、D。、およびB. Stewart、「インターネット標準管理フレームワークの紹介と適用声明」、RFC 3410、2002年12月。
[RFC3418] Presuhn, R., "Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)", STD 62, RFC 3418, December 2002.
[RFC3418] Presuhn、R。、「単純なネットワーク管理プロトコル（SNMP）の管理情報基盤（MIB）」、STD 62、RFC 3418、2002年12月。
Authors' Addresses
著者のアドレス
Clay Sikes Zhone Technologies, Inc. Florida Design Center 8454 126th Ave. N. Largo, FL 33773 US
Clay Sikes Zhone Technologies、Inc。Florida Design Center 8454 126th Ave. N. Largo、FL 33773 US
Phone: +1 727 530 8257
Fax: +1 727 532 5698
EMail: csikes@zhone.com
Bob Ray PESA Switching Systems, Inc. 330-A Wynn Drive Huntsville, AL 35805 US
ボブ・レイペサスイッチングシステム、330-Aウィンドライブハンツビル、アラバマ州35805米国
Phone: +1 256 726 9200 ext. 142
Fax: +1 256 726 9271
EMail: rray@pesa.com
Rajesh Abbi Alcatel USA 2301 Sugar Bush Road Raleigh, NC 27612 US
Rajesh Abbi Alcatel USA 2301 Sugar Bush Road Raleigh、NC 27612 US
Phone: +1 919-850-6194
Fax: +1 919-850-6670
EMail: Rajesh.Abbi@alcatel.com
Full Copyright Statement
完全な著作権声明
Copyright (C) The Internet Society (2005).
Copyright（c）The Internet Society（2005）。
This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights.
この文書は、BCP 78に含まれる権利、ライセンス、および制限の対象となり、そこに記載されている場合を除き、著者はすべての権利を保持しています。
This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
このドキュメントとここに含まれる情報は、「現状のまま」に基づいて提供されています。また、貢献者、彼/彼女が代表する組織（もしあれば）が後援する組織、インターネット協会とインターネット工学タスクフォースは、すべての保証、明示的または明示的、またはすべての保証を否認します。本書の情報の使用が、商品性または特定の目的に対する適合性の権利または黙示的な保証を侵害しないという保証を含むがこれらに限定されないことを含む。
Intellectual Property
知的財産
The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79.
IETFは、知的財産権またはその他の権利の有効性または範囲に関して、本書に記載されている技術の実装または使用、またはそのような権利に基づくライセンスに基づくライセンスの範囲に関連すると主張される可能性のある他の権利に関しては、立場を取得しません。利用可能になります。また、そのような権利を特定するために独立した努力をしたことも表明していません。RFCドキュメントの権利に関する手順に関する情報は、BCP 78およびBCP 79に記載されています。
Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr.
IETF事務局に行われたIPR開示のコピーと、利用可能にするライセンスの保証、またはこの仕様の実装者またはユーザーによるそのような独自の権利の使用のための一般的なライセンスまたは許可を取得しようとする試みの結果を取得できます。http://www.ietf.org/iprのIETFオンラインIPRリポジトリから。
The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org.
IETFは、関心のある当事者に、著作権、特許、または特許出願、またはこの基準を実装するために必要な技術をカバーする可能性のあるその他の独自の権利を注意深く招待するよう招待しています。ietf-ipr@ietf.orgのIETFへの情報をお問い合わせください。
Acknowledgement
謝辞
Funding for the RFC Editor function is currently provided by the Internet Society.
RFCエディター機能の資金は現在、インターネット協会によって提供されています。